![background image](http://html.mh-extra.com/html/hyundai/s2f57-ac300/s2f57-ac300_installation-instructions-manual_2197280001.webp)
Genuine Accessories
Glasses
Gloves
Mask
Hearing Protection
Part Weight (Gross)
FMVSS 110 Compliance Information
Technical Support
1
Read the entire Installation Instructions prior to beginning the installation of the part.
2
Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
3
Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.
4
NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
5
Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.
6
Record radio presets prior to disconnecting battery power, if needed.
7
Roll down the driver's window and adjust the power seats (if applicable) prior to disconnecting battery power, if needed.
8
To prevent stress on the remote start wire harness, ensure the tilt steering column is fully extended before installing the kit.
9
Vehicle should be at room temperature.
10
10mm Deep Well
Socket
8mm Socket
Extension
Wire Cutters
Trim Removal Tool
N
O
T
E
Denotes important information to be
reviewed during the step
Denotes cautions to be taken to avoid
vehicle and component damage
Ratchet
12mm Socket
Authorized dealers use:
Hours:
Clean Cloth
50/50 Isopropyl Alcohol
(70%) and Water Mix
Torque wrench
Notes to the installer:
Language
English
5/3/2018
Rev. Date
Accessory:
Vehicle Model:
Difficulty stated above reflects the minimum level of
expertise required to install the accessory:
( B )
Remote Engine Start - Key Start
(A) Customer
Santa Fe
Difficulty:
Part No.
Model Year
Copy OEM Logo Here (
→)
2019~
S2F57 AC300
Note:
Basic Required Tools
(C) Master Technician or Specialist
(B) Dealer Technician
Instructional Symbols / Definitions
Application Notes
Denotes quality processes to be checked
prior to moving to the next step
Denotes personal protective equipment (PPEs) that
may be required for a step. Examples of safety
equipment icons noted below:
Denotes specific tools that are necessary
to complete a step
#2 Phillips
Screwdriver
Denotes cautions to be taken to avoid
physical injury or electronic component
damage
Vehicle must be equipped with mechanical key start.
Ensure vehicle does NOT have SMART KEY (PUSH BUTTON IGNITION SYSTEM).
Vehicle should be equipped with automatic transmission, power door locks, and power windows. If these features are not equipped on the vehicle, do not proceed with install.
(1) 855-225-7344
M~F - 9am~5pm Pacific Standard Time
The order of the disassembly and reassembly steps have been optimized for maximum efficiency and the correct
installation of the Remote Engine Start kit. Disassemble vehicle components (including harness connectors) and
install the kit components according to each step, as indicated. Avoid disassembling or reassembling any
components in advance to prevent unnecessary labor time and/or installation errors.
Denotes warnings that may lead to serious
physical injury or vehicle damage
0.87
0.39
lbs
kg
All dealers must determine if the weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed
options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load
Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying
capacity in kilograms or pounds, which is the total weight of all added options and accessories.
Load Label Part Number: NP070-09003
Revision Date
5/03/2018
Page 1 of 11