Hyster D010, Техника безопасности, техническое обслуживание и ремонт

Страница: 32 / 38

Engine Specifications 600 SRM 496
– Grinding Limit ............ 0.75 mm (0.030 in.)
Clearance Between
Journals and Main
Bearings.............................. 0.031 to 0.049 mm
(0.0012 to 0.0019 in.)
– Service Limit............... 0.08 mm (0.003 in.)
Connecting Rod Journal
Diameter............................. 50.940 to 50.955 mm
(2.0055 to 2.0061 in.)
– Service Limit............... 0.05 mm (0.002 in.)
– Grinding Limit ............ 0.75 mm (0.030 in.)
Thrust Bearing
Clearance............................ 0.08 to 0.18 mm
(0.003 to 0.007 in.)
– Service Limit............... 0.30 mm (0.012 in.)
CONNECTING RODS
Small End Bore .................. 21.943 to 21.961 mm
(0.8639 to 0.8646 in.)
Clearance Between
Piston Pin and
Bore..................................... 0.015 to 0.040 mm
(0.0006 to 0.0016 in.)
Clearance Between
Crankshaft Journals
and Rod Bearings ............... 0.027 to 0.067 mm
(0.0011 to 0.0026 in.)
– Service Limit............... 0.10 mm (0.004 in.)
CYLINDER BLOCK
Distortion at Top Surface... 0.15 mm (0.0059 in.)
Bore Diameter .................... 86.00 to 86.019 mm
(3.3858 to 3.3866 in.)
– Wear Limit .................. 0.15 mm (0.0059 in.)
PISTONS
Diameter............................. 85.944 to 85.964 mm
(3.3836 to 3.3844 in.)
Clearance Between
Piston and Bore .................. 0.036 to 0.075 mm
(0.0014 to 0.0030 in.)
– Service Limit............... 0.15 mm (0.0059 in.)
Piston Pin Diameter .......... 21.974 to 21.980 mm
(0.8651 to 0.8654 in.)
Groove Width for Piston
Rings Nos. 1 and 2 ............. 1.520 to 1.540 mm
(0.0598 to 0.0606 in.)
Groove Width for
Oil Ring............................... 4.020 to 4.040 mm
(0.1583 to 0.1591 in.)
Piston Ring Clearance in
Groove (Nos. 1 and 2) ........ 0.03 to 0.07 mm
(0.0012 to 0.0028 in.)
– Service Limit............... 0.15 mm (0.0059 in.)
Piston Ring End Clearance:
– Top Ring ...................... 0.20 to 0.35 mm
(0.008 to 0.014 in.)
– Second Ring................. 0.15 to 0.30 mm
(0.006 to 0.012 in.)
– Oil Control Ring.......... 0.30 to 0.90 mm
(0.012 to 0.035 in.)
– Service Limit
(All Rings) ...................... 1.0 mm (0.039 in.)
OIL PUMP
Clearance Between
Inner Gear and Crescent ... 0.267 to 0.380 mm
(0.0105 to 0.0150 in.)
– Service Limit............... 0.40 mm (0.0157 in.)
Clearance Between
Crescent and Outer Gear... 0.20 to 0.32 mm
(0.008 to 0.013 in.)
– Service Limit............... 0.35 mm (0.014 in.)
Clearance Between Outer
Gear and Housing .............. 0.090 to 0.184 mm
(0.0035 to 0.0072 in.)
– Service Limit............... 0.20 mm (0.008 in.)
Side Clearance Between
Gears and Housing ............ 0.03 to 0.063 mm
(0.0012 to 0.0025 in.)
– Service Limit............... 0.10 mm (0.004 in.)
28