Hyster B60-80XT Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 21

background image

1800 SRM 535

Brake Shoe Removal

1.

ARM CAM WELDMENT

2.

COTTER PIN

3.

FLAT WASHER

4.

NUT

5.

LOCKWASHER

6.

ADJUSTING NUT

7.

LUBE FITTING

8.

SNAP RING

9.

CAPSCREW

10. LOCKWASHER
11. SUPPORT WELDMENT

12. BUSHING
13. CENTERING SHAFT
14. NUT
15. NUT
16. BRAKE SHAFT
17. ADJUSTING SCREW-UPPER
18. SPRING
19. ADJUSTING SCREW-LOWER
20. SETSCREW SEAT
21. SETSCREW
22. BRAKE SHOE W/LINING

Figure 4. Brake Shoe Assembly (C60-80XT)

6.

Disassemble the snap rings from the brake pivot
pins.

Remove the cotter pin and flat washer

retaining the arm cam weldment to the support
weldment. Remove the capscrew and lockwasher
supporting the centering shaft to the support
weldment.

Remove the support weldment.

Check the bushing in the support weldment for
elongation or damage. Replace the bushing if
necessary.

Refer to WARNINGS in Repairs -

General.

CA/C60-80XT/XT2, T5XT

1.

Remove the two jam nuts from the bottom of the
brake shaft. Loosen the hex nut on the top of the
brake shaft. Loosen the setscrews retaining the
adjusting screws. Loosen the adjusting screws.
Remove the brake shaft out of the arm cam weld-
ment, brake shoes, and centering shaft. Support
the springs when removing the brake shaft.

5

«
...
5
6
7
8
9
...
»

Содержание B60-80XT






















Отзывы:

Нет отзывов

Похожие инструкции для B60-80XT

Бренд: H&M Страницы: 37

Grout Hog UGPH75

Бренд: EZG Страницы: 15

Бренд: EP Equipment Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды