background image

8000 SRM 1009

General

General

WARNING

DO NOT make repairs or adjustments unless
you have been properly trained and authorized
to do so. Repairs and adjustments that are not
correct can create dangerous operating condi-
tions.

DO NOT operate a lift truck that needs repairs.
Report the need for repairs to your supervisor
immediately. If repair is necessary, attach a DO
NOT OPERATE tag to the control handle and
remove the key from the key switch.

This section contains the instructions for periodic
maintenance and inspection and a Maintenance
Schedule.

The Maintenance Schedule has time intervals for in-
spection, lubrication, and periodic maintenance. The
time intervals are based on a normal operation. Nor-
mal operation is considered to be one eight hour shift
per day in a relatively clean environment on an im-
proved surface. Multiple shifts, dirty operating con-
ditions, etc. will reduce the time intervals between
services recommended in the Maintenance Schedule.

NOTE:

The front end of the lift truck is the control

handle end. Forward travel is movement with the
forks trailing. Rear travel is movement in the direc-
tion of the forks. The right hand side of the lift truck
is to the operator’s right hand, facing the truck from
the control handle end in the position for operating
the controls.

Your Hyster

®

lift truck dealer has the trained per-

sonnel and equipment to do a complete program of
inspection, lubrication, and maintenance. This com-
plete program will help your lift truck operate better
over a longer period of time.

Some users have service personnel and facilities to
do the items listed in the Maintenance Schedule.
Service Manuals are available from your Hyster lift
truck dealer to help users who do their own repairs.

HOW TO MOVE A DISABLED TRUCK

This lift truck is not normally towed. If the traction
system will not operate, make repairs at the location
if possible. If the lift truck must be towed, refer to
the Maintenance Manual.

How to Tow the Lift Truck

WARNING

Never carry a disabled lift truck unless the lift
truck MUST be moved. The lift truck used to
lift the disabled lift truck MUST have a rated
capacity equal to or greater than the weight of
the disabled lift truck. The capacity must be
for a load center equal to half the width of the
disabled lift truck. See the capacity plate on
the disabled lift truck for the approximate total
weight. The forks must extend the full width
of the disabled lift truck. Put the weight of the
disabled lift truck at the center of the forks and
be careful not to damage the under side of the
disabled lift truck.

Make sure no one except the driver is near the
lift trucks during towing. Both the tow truck
and the disabled truck can cause personal in-
jury during towing.

Stay clear of the tow chain, towing vehicle, and
the lift truck during the towing operation to
prevent personal injury.

Until repairs are complete, keep a DO NOT OP-
ERATE tag on the control handle. Remove the
key.

To avoid personal injury, use extra care when
moving a lift truck during the following condi-
tions:
• Brake does not operate correctly.
• Steering does not operate correctly.
• Tire is damaged.
• Traction conditions are bad.
• The lift truck must be moved up a steep

grade.

CAUTION

Never tow the lift truck faster than the speed
of a person walking. Steering can be difficult
and motor damage can occur at higher speeds.
Always travel smoothly without sudden starts.

The electric brake must be released before the lift
truck can be moved. If there is not sufficient battery
power, placing the control handle in the operating
position will not release the electric brake. Use the
control handle to steer the lift truck while it is being
towed. Use one hand and walk to one side of the lift

1

Содержание B218



























Отзывы: