HySecurity SlideDriver 50VF2 страница 4 Скачать руководство пользователя | Manualshive

Страница: 4 / 86

background image

SlideDriver Addendum D0395 Rev. E Page 2

www.hysecurity.com © 2012 10/18/2012

G

rooVed

d

riVe

r

ail

The grooved drive rail has become the standard for all new SlideDriver gate operator installations.

In this manual, several illustrations show the non-grooved, flanged drive rail which is no longer available un-
less a Solenoid Lock option is installed.

The grooved drive rail replaces the non-grooved, flanged drive rail.

A section of the two different drive rails is shown in the illustration.

The small grooves on the underside of the new drive rail improve traction in slick or wet conditions and
provide more pulling and stopping power in SlideDriver installations. The three underside flanges have
been eliminated which reduces drive wheel wear and drag in misaligned gate installations. Additionally, the
no-flange drive rail stacks better for shipping which reduces the likelihood of freight damage.

NOTE: T

he non-grooved, flanged drive rail is standard and will be on your order unless you specify other

-

wise. The non-grooved, flanged drive rail is only available when using the Solenoid Lock option. The Sole

-

noid Lock option requires an outer edge flange and therefore must be installed with the non-grooved,
flanged drive rail.

Standard grooved drive rail

Non-grooved, flanged drive rail

No flanges

Grooves on the underside

NOTE:

Solenoid Lock option

requires flanged drive rail

Grooved versus non-grooved, flanged drive rail

Scan QR code for Smart
Phone access to HySecurity
website information.

Tech Support: 800-321-9947

«
...
2
3
4
5
6
...
»

Содержание SlideDriver 50VF2























































































Отзывы:

Нет отзывов

Похожие инструкции для SlideDriver 50VF2

Бренд: FAAC Страницы: 4

LiftMaster Security+ 1210EM FS2

Бренд: Chamberlain Страницы: 80

Бренд: ECOSTAR Страницы: 40

Бренд: Tenpilot Страницы: 24

Gizmo EM100 Series

Бренд: Black & Decker Страницы: 2

Бренд: Black & Decker Страницы: 2

Бренд: Winco Страницы: 8

Бренд: SOMFY Страницы: 60

Бренд: SOMFY Страницы: 80

Бренд: moore o matic Страницы: 32

Бренд: Power Drive Страницы: 40

Бренд: Power Drive Страницы: 36

AXOVIA 180 B NS

Бренд: SOMFY Страницы: 12

Бренд: SOMFY Страницы: 24

Бренд: SOMFY Страницы: 24

Бренд: Toastmaster Страницы: 9

GDO-6v4 EasyRoller

Бренд: Automatic Technology Страницы: 36

Gold400A Series

Бренд: V2 Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды