HyQuest Solutions iRIS 270 Скачать руководство пользователя | Manualshive

Страница: 37 / 137

background image

© 2022 HyQuest Solutions

37

Configuration

3.4.3.2

Digital I/O

Output Mode:

Choose the operating mode of the output from the available options. Valid digital output
modes are:

Mode

Description

Disabled

The Digital I/O channel will operate as a digital input.

Schedule

Follows the schedule as defined by the settings.

Schedule Plus

Follows the schedule as defined by the settings. Also activate the output
when  a  user  is  logged  in  or  an  RS232  Telemetry  mode  call-in  is  in
progress.  If  a  user  is  logged  on  via  the  LCD/keypad  interface  OR  the
power  mode  is  set  to  RS232  Telemetry  and  an  alarm  requiring
transmission to a base station is pending, the output will be on.

Alarm

The output is on if any sensor alarm is active. Turns off when all alarms
are inactive.

Remote

Remote Control from HydroTel or via a custom script. DIO1 is controlled
by bit 0 of d1000, DIO2 by bit 1 of d1000, DIO3 by bit 2 of d1000 and
DIO4 by bit 3 of d1000.

Online (DBA)

Follow wireless link state i.e. the output is on if the wireless modem is on-
line (for Daughter board in slot A).

Online (DBB)

Follow wireless link state i.e. the output is on if the wireless modem is on-
line (for Daughter board in slot A).

On

Always on.

Off

Always off (as opposed to tristate).

Table 9 – Digital Output Modes

«
...
35
36
37
38
39
...
»

Содержание iRIS 270










































































































































Отзывы:

Нет отзывов

Похожие инструкции для iRIS 270

Бренд: Escort Страницы: 28

OM-CP-PRTRANSIS-A2 OM-CP-PRTRANSIS-A2

Бренд: Omega Engineering Страницы: 6

BioNomadix Logger

Бренд: BIOPAC Systems, Inc. Страницы: 28

Бренд: Extech Instruments Страницы: 5

Бренд: Extech Instruments Страницы: 7

Бренд: Extech Instruments Страницы: 10

Бренд: Chauvin Arnoux Страницы: 86

Бренд: Design Analysis Страницы: 272

Бренд: Fimer Страницы: 29

Бренд: YOKOGAWA Страницы: 51

CSI-GL-WIFI-STICK

Бренд: CanadianSolar Страницы: 19

CT485B-110V-G-AL

Бренд: Omega Страницы: 64

OM-CP-RFRHTemp2000A

Бренд: Omega Страницы: 15

Бренд: METER Страницы: 2

Бренд: METER Страницы: 3

Бренд: EWS Страницы: 18

Бренд: Next Страницы: 59

Бренд: Next Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды