background image

Hypro warrants to the original purchaser of its products (the “Purchaser”) that such products will be free from defects in material and

workmanship under normal use for the period of one (1) year for all products except: oil crankcase plunger pumps will be free from

defects in material and workmanship under normal use for the period of five (5) years, and accessories will be free from defects in

material and workmanship under normal use for the period of ninety (90) days. In addition, Hypro warrants to the purchaser all forged

brass pump manifolds will be free from defects in material and workmanship under normal use and from damage resulting from

environmental conditions for the life of the pump.

“Normal use” does not include use in excess of recommended maximum speeds, pressures, vacuums and temperatures, or use

requiring handling of fluids not compatible with component materials, as noted in Hypro product catalogs, technical literature, and

instructions. This warranty does not cover freight damage, freezing damage, normal wear and tear, or damage caused by

misapplication, fault, negligence, alterations, or repair that affects the performance or reliability of the product.

THIS WARRANTY IS EXCLUSIVE. HYPRO MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING BUT NOT

LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Hypro’s obligation under this warranty is, at Hypro’s option, to either repair or replace the product upon return of the entire product to

the Hypro factory in accordance with the return procedures set forth below.  

THIS IS THE EXCLUSIVE REMEDY FOR ANY

BREACH OF WARRANTY.

IN NO EVENT SHALL HYPRO BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND,

WHETHER FOR BREACH OF ANY WARRANTY, FOR NEGLIGENCE, ON THE BASIS OF STRICT LIABILITY, OR OTHERWISE.

Return Procedures

All pumps or products must be flushed of any chemical (ref. OSHA Section 0910.1200 (d)(e)(f)(g)(h) and hazardous chemicals must

be labeled before being shipped* to Hypro for service or warranty consideration. Hypro reserves the right to request a Material Safety

Data sheet from the Purchaser for any pump or product Hypro deems necessary. Hypro reserves the right to “disposition as scrap”

pumps or products returned which contain unknown substances, or to charge for any and all costs incurred for chemical testing and

proper disposal of components containing unknown substances. Hypro requests this in order to protect the environment and

personnel from the hazards of handling unknown substances.

For technical or application assistance, call the Hypro Technical/Application number: 800-445-8360.

To obtain service or warranty assistance, call the Hypro Service and Warranty number: 800-468-3428; or call the Hypro Service and

Warranty FAX: (651) 766-6618.

Be prepared to give Hypro full details of the problem, including the following information:

1. Model number and the date and from whom you purchased your pump.

2. A brief description of the pump problem, including the following:

• Liquid pumped. State the pH and any non-soluble 

• Drive type (gas engine/electric motor; direct/belt drive; 

materials, and give the generic or trade name. 

tractor PTO)  and rpm of pump.

• Temperature of the liquid and ambient environment.

• Viscosity (of oil, or other than water weight liquid).

• Suction lift or vacuum (measured at the pump). 

• Elevation from the pump to the discharge point.

• Discharge pressure. 

• Size and material of suction and discharge line.

• Size, type, and mesh of the suction strainer. 

• Type of spray gun, orifice size, unloader/relief valve.

Hypro may request additional information, and may require a sketch to illustrate the problem.  Contact the factory to receive a return

material authorization before sending the product. All pumps returned for warranty work should be sent shipping charges prepaid to:

HYPRO

Attention: Service Department

375 Fifth Avenue NW

New Brighton, Minnesota 55112

*Carriers, including U.S.P.S., airlines, UPS, ground freight, etc., require specific identification of any hazardous materials being

shipped. Failure to do so may result in a substantial fine and/or prison term. Check with your shipping company for specific

instructions.

Hypro 2008

Printed in the USA

Limited Warranty on Hypro Pumps 

Содержание 1802C





















Отзывы: