Hypertherm PAC500 Скачать руководство пользователя | Manualshive

Страница: 12 / 96

background image

SAFETY

1-4

Hypertherm

Plasma Systems

4-99

SAFETY

Instant-On Torches
Plasma arc comes on immediately when the torch
switch is activated.

A PLASMA ARC CAN CAUSE INJURY AND BURNS

The plasma arc will cut quickly through gloves and
skin.
• Keep away from the torch tip.
• Do not hold metal near the cutting path.
• Never point the torch toward yourself or others.

Eye Protection Plasma arc rays produce intense
visible and invisible (ultraviolet and infrared) rays that
can burn eyes and skin.
• Use eye protection in accordance with applicable

national or local codes.

• Wear eye protection (safety glasses or goggles with

side shields, or a welding helmet) with appropriate
lens shading to protect your eyes from the arc’s
ultraviolet and infrared rays.

Lens Shade

Arc Current

AWS (USA)

ISO 4850

Up to 100 A

No. 8

No. 11

100-200 A

No. 10

No. 11-12

200-400 A

No. 12

No. 13

Over 400 A

No. 14

No. 14

ARC RAYS CAN BURN EYES AND SKIN

Skin Protection Wear protective clothing to protect
against burns caused by ultraviolet light, sparks and
hot metal.
• Gauntlet gloves, safety shoes and hat.
• Flame-retardant clothing to cover all exposed areas.
• Cuffless trousers to prevent entry of sparks and

slag.

• Remove any combustibles, such as a butane lighter

or matches, from your pockets before cutting.

Cutting Area Prepare the cutting area to reduce
reflection and transmission of ultraviolet light:
• Paint walls and other surfaces with dark colors to

reduce reflection.

• Use protective screens or barriers to protect others

from flash and glare.

• Warn others not to watch the arc. Use placards or

signs.

Work Cable Attach the work cable securely to the
workpiece or the work table with good metal-to-metal
contact. Do not connect it to the piece that will fall
away when the cut is complete.

Work Table Connect the work table to an earth
ground, in accordance with appropriate national or
local electrical codes.

GROUNDING SAFETY

Input Power
• Be sure to connect the power cord ground wire to

the ground in the disconnect box.

• If installation of the plasma system involves

connecting the power cord to the power supply, be
sure to connect the power cord ground wire
properly.

• Place the power cord's ground wire on the stud first,

then place any other ground wires on top of the
power cord ground. Fasten the retaining nut tightly.

• Tighten all electrical connections to avoid excessive

heating.

«
...
10
11
12
13
14
...
»

Содержание PAC500

































































































Отзывы:

Нет отзывов

Похожие инструкции для PAC500

Бренд: 3M Страницы: 8

Бренд: Jasic Страницы: 30

Бренд: Teac Страницы: 3

Subwoofer KHT2005.2

Бренд: KEF Страницы: 2

Бренд: KEF Страницы: 7

Бренд: KEF Страницы: 4

MCX-A10 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 56

Бренд: Genie Страницы: 202

Бренд: Vestil Страницы: 11

TIG 160 DC Lift

Бренд: GYS Страницы: 20

Бренд: ADEMCO Страницы: 40

Бренд: Ramsey Electronics Страницы: 2

Бренд: Omega Страницы: 16

Бренд: AmeriWater Страницы: 67

Бренд: Advent Страницы: 32

ID PULSE Series

Бренд: Magmaweld Страницы: 8

Бренд: Aiwa Страницы: 4

Бренд: Hyun Joung System Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды