Hypertherm Echion Скачать руководство пользователя страница 93

Страница: 93 / 194

Preventive maintenance

Echion

Operator

Manual 810770

even

tive maint

enance

Prepare for storage

Use this procedure to prepare the system for storage. Clearing the water lines prevents freezing,
which can cause damage to the pump.

Refer to

Connect the water and the air

on page 157 for information about the connections.

Parts, tools, and materials

WARNING

High-pressure water can cause eye injuries. Wear approved eye protection when operating or
doing work near this equipment.

Do not stand over components such as tubes or valves while drying the system.

All low-pressure water connections use push-to-connect fittings.

Cutting water in

Boost pump

Inlet water solenoid (for systems
without a boost pump)

Waste water out

Compressed air

Cutting water out

Water-cooled system

Cooling in

Cooling out

1/8-inch male to 1/2-inch male adapter
(compressed air to

cutting water in

)

1/8-inch male to 1-inch male adapter
(compressed air to

cooling in

)

7/16-inch open-ended wrench

1-1/16-inch open-ended wrench

Filter wrench (included in the standard tool kit)

Water-cooled system

1-inch open-ended wrench

1-3/16-inch open-ended wrench

Содержание Echion



































































































































































































Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды

Hypertherm Echion, Руководство оператора

Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды