Hypertherm Echion Скачать руководство пользователя страница 91

Страница: 91 / 194

Preventive maintenance

Echion

Operator

Manual 810770

even

tive maint

enance

Postmaintenance start procedure

A smooth start after maintenance can give the high-pressure seal longer life.



Touch the

symbol to stop the procedure and to turn

OFF

the pump.

Use this program to increase the water pressure gradually. The procedure takes
approximately 6 minutes. Refer to

Touchscreen maps

on page 177 for details about the program.

Turn

the utility water to the pump.

Turn

the compressed air source.

Turn

the electrical main (line disconnect switch).

Turn the primary breaker disconnect lever on the electrical enclosure door to

Make sure that the EMERGENCY STOP is not engaged. If the button is pushed in, turn the
button clockwise until it releases.

Make sure that the key switch is set to Local

Push the Controls button.

On the operator interface, touch the maintenance symbol to open the primary maintenance
screen.

Touch this symbol to open the

Start Procedure

screen.

10.

Touch the symbol on the screen to start the procedure.

11.

When

Turn On the Cutting Head

flashes on the screen:

Move the cutting head to a safe location on the table.

Turn

the cutting head.

Touch the

symbol to continue.

While the procedure continues, examine the pump for high-pressure water leaks and
hydraulic fluid leaks. Monitor these areas.



Hydraulic connections



Valves



Intensifier bridge and bottom deck

Содержание Echion



































































































































































































Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды

Hypertherm Echion, Руководство оператора

Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды