Hypertech POWER PROGRAMMER III Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 31

Hypertech POWER PROGRAMMER III Скачать руководство пользователя страница 6

5

INFO

SBA

RADIO AMP

TREC

SEO B1

RADIO

EAP

W/S WASH

W/S WASH

CRANK

BTSI

A/C COMP

RR WPR

The fuse panel is located on the driver’s
side of the vehicle behind the vehicle battery.
Lift off the cover to access the fuse block.
You now can remove the fuse. To remove
the fuse, hold the end of the fuse between
your thumb and index finger and pull
straight out.

Make sure you remember

to re-install the fuse in the proper location
and re-install the fuse panel cover after
programming your vehicle.

Fuse panel

cover

For All 4.8/5.3/6.0/8.1L
GM vehicles

TBC

HAZ LP

RR WPR

RDO AMP

CIGAR

HTD MIR

SEO 2

RADIO

CTSY LP

IGN C

FOG LP

BTSI

FOG LP

AUX PWR

A/C

A/C

HORN

HORN

W/W PMP

DRL

SEO 1

1999-2002 GM vehicle fuse diagram

** Do Not Turn The Ignition Key Off **

1. Disconnect the programmer from the vehicle.
2. Reconnect the programmer to the vehicle.
3. Press the START button on the programmer.

The programmer will resume communications with the vehicle

where it left off. If the programmer fails to re-establish communi-
cations with the vehicle, repeat the procedure. If the programmer
still fails to resume, disconnect the programmer and turn the
vehicle off. Attempt to start your vehicle. If your vehicle fails to
start, the vehicle computer may have been corrupted, and you
will need to send your vehicle computer and programmer to
Hypertech for repair. If the vehicle starts, you will need to return
your programmer to Hypertech for re-initialization, no harm was
done to the vehicle computer.

For 1999-2002 vehicles

, the one (1) fuse that must be removed is

as follows: (see highlighted fuse location above.)
Location

Description

SEO1

Special Equipment Option, OnStar

For 2003-2005 vehicles

, the one (1) fuse that must be removed is

as follows: (see highlighted fuse location below.)

Location
INFO

Description
OnStar

NOTE: Owner’s manual fuse diagram may vary from examples shown.

2003-2005 GM vehicle fuse diagram

(Illustration does not represent entire fuse diagram)

«
...
4
5
6
7
8
...
»

Содержание POWER PROGRAMMER III
































Отзывы:

Нет отзывов