Hypertech POWER PROGRAMMER III Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 31

Hypertech POWER PROGRAMMER III Скачать руководство пользователя страница 10

9

SECTION 3: PROGRAMMING INSTRUCTIONS

• Connect one (1) end of the provided cable to the programmer

as in Figure D and tighten the two (2) thumbscrews.

• See Figure E. Locate the Data Link Connector (DLC) under the

driver’s side of the dash panel above the emergency brake.

• Plug the programmer cable into the DLC. Make sure the cable

is plugged in completely to ensure a good connection.

• Set the parking brake to turn off the DRLs (Day-Light Running

Lamps) and turn the ignition key to the RUN position, but do
not start the engine.

IMPORTANT:

-DO NOT leave the vehicle while programming is in process.

-Make sure the vehicle battery is fully charged before programming.

-The key must remain in the RUN position, without the engine

running, during the entire programming process.

-DO NOT operate electrical accessories

(radio, windows, wipers, etc.) while programming.

- If the vehicle is equipped with an OnStar system, make sure

the system is temporarily disabled (see Section 1 for details).

- DO NOT attempt programming while the

vehicle is connected to a battery charger.

Figure D

Programmer

Thumbscrew

Thumbscrew

Figure E

«
...
8
9
10
11
12
...
»

Содержание POWER PROGRAMMER III
































Отзывы:

Нет отзывов