Hydronix Hydro-Control VI Скачать руководство пользователя страница 24

Страница: 24 / 104

Electrical Installation

Chapter 3

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0

1.5

Analogue I/O Connector (on optional Expansion Board)

Pins

Name

Description

Analogue Out 2

Analogue output reserved for future use.

Analogue Out 1

Analogue output reserved for future use.

Analogue In

Analogue input reserved for future use.

Weigh Scale

Analogue weigh scale input for weighed water system.

2 Power Supply

The unit uses 24v DC, with a nominal power rating of 24W including the sensor.

Minimum supply:

24v DC, 1.25A (30W)

Recommended supply: Hydronix part number 0116
Important:

If using 24v DC for inputs/outputs (valves, etc), then this should be

powered from a separate power supply to the main unit to reduce the

likelihood of interference between the two systems.

3 Communications

3.1

RS485

The RS485 connection is used for communicating with a Hydronix moisture sensor. It is

possible to change operating parameters and sensor diagnostics from the Hydro-Control.

3.2

RS232

The RS232 connection is used for connection to a batch computer or remote operator terminal

to permit the remote selection of recipes.

3.3

Ethernet Telnet Port

Enables the same operations available on the RS232 using the Telnet port (port23).

4 Interface modules

4.1

OPTO-22 Modules

The Hydro-Control is fitted with plug-in optically isolated input/output modules, manufactured

by OPTO-22. A range of different input/output modules is available depending on the voltage

required.

Seven output modules and five input modules are provided. The FINE WATER output MUST

be connected for the unit to function correctly. All other connections are optional and can be

connected as appropriate for each configuration.

Содержание Hydro-Control VI









































































































Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды

Hydronix Hydro-Control VI, Руководство по установке

Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды