manualshive.com logo in svg

Hydronix HV04, Руководство пользователя

Поделиться
Скачать
Hydronix HV04 Скачать руководство пользователя страница 83

 

Hydro-View User Guide HD0531 Rev 2.0.0 83 

Appendix C 

Quick Start Rules 

1  Quick Start Rules 

•

 

Limiting slopes (B) for any calibration will be a maximum of 2.0 and a minimum of 0.06. 

•

 

One-point calibrations: 

•

 

The calibration slope will be set to be the average of the two known sand calibrations. 

•

 

If the Unscaled value at zero moisture is less than 5 the Unscaled value at zero 
moisture will be set to be 5 and a new calibration slope calculated through this point 
and the single point entered. 

•

 

If the Unscaled value at zero moisture is greater than 50 the Unscaled value at zero 
moisture will be set to be 50 and a new calibration slope calculated through this point 
and the single point entered. 

•

 

If the resulting slope is greater than the maximum or less than the minimum calibration 
slopes then no calibration will be carried out and the user will be informed of this. 

•

 

More than 1 point calibration – spread in points: Moisture < 1% or Unscaled < 2 

•

 

A single point calibration will be carried out. 

•

 

More than 1 point calibration – spread in points: Moisture < 3% or Unscaled < 6 

•

 

If the calculated slope is greater than the selected materials quick start calibration 
slope set the calculated slope to the quick start calibration slope -  If the calculated 
slope is less than the selected quick start calibration slope set the calculated slope to 
the quick start calibration slope –  otherwise leave the slope as it is. (Recalculate 
intercept value from average from all points) 

•

 

If the Unscaled value at zero moisture is less than 5 the Unscaled value at zero 
moisture will be set to be 5 and a new calibration slope calculated through this point 
and the average of the points entered. 

•

 

If the Unscaled value at zero moisture is greater than 50 the Unscaled value at zero 
moisture will be set to be 50 and a new calibration slope calculated through this point 
and the average of the points entered. 

•

 

If the resulting slope is greater than the maximum or less than the minimum calibration 
slopes then no calibration will be carried out and the user will be informed of this. 

•

 

More than 1 point calibration – spread in points: Moisture > 3% and Unscaled > 6 

•

 

Calibration slope is calculated and the user is warned if: 

•

 

If the Unscaled value at zero moisture is less than 5. 

•

 

If the Unscaled value at zero moisture is greater than 50. 

•

 

If the resulting slope is greater than the maximum or less than the minimum 
calibration. 

 

 

Содержание HV04






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды