manualshive.com logo in svg

Hydronix HV04, Руководство пользователя

Поделиться
Скачать
Hydronix HV04 Скачать руководство пользователя страница 15

 

Hydro-View User Guide HD0531 Rev 2.0.0 15 

Chapter 1 

Introduction 

 

Figure 1: The Hydro-View  

 

This Hydro-View User Guide is only valid for model number HV04 running software 
version 2.0.0 and above. User guides for earlier Hydro-View model numbers are available 
from www.hydronix.com

 

1  Introduction to the Hydro-View (HV04) 

The Hydro-View  is a touch screen computer based upon the Microsoft Windows CE operating 
system that has been designed to work with the Hydronix range of sensors to provide a live 
display of on-line process measurements and enable quick and easy calibration and 
configuration of the sensors. The Hydro-View can connect to up to 16 sensors at one time. 

Its main display page supports 1, 2 or 4 screen areas, each of which is configurable to display a 
trend graph or numeric display of measurements from any connected sensor. 

The Hydro-View stores multiple material calibrations for each sensor, allowing rapid re-calibration 
if the material  being measured is changed. The intuitive multi-point calibration feature enables 
the sensor to be easily and precisely calibrated. 

As well as being connected to a Hydro-View, the sensors can also be integrated with a control 
system via their analogue outputs. Digital inputs and outputs on the sensors allow for averaging 
start and stop in a batch process. 

In order to correctly understand the use of the Hydro-View unit it is important to understand the 
capabilities of the sensor that is to be attached to the unit.  Please read the relevant user guide 
that is supplied with the sensor.  Alternatively please download the user guide from the Hydronix 
website: www.hydronix.com  

All sensor configuration options in this guide reference Hydronix sensors utilising firmware 
HS0102 or above. Some facilities detailed will not be available with all sensors. 

Содержание HV04






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды