In
Out
Heat pump
Valve 1
Valve 2
Valve 3
In
Out
Pool
Pump/Filter
Contents:
2 x PVC T-piece Ø 50mm
3 x PVC ball valve Ø 50mm
4 x SS hose clamp
4 x hose tail Ø 50mm – 38/32mm
4 x PVC pipe 10cm Ø 50mm
1 x PVC glue 100ml
1 x PVC cleaner 125ml
T-piece
PVC pipe
PVC pipe
PVC pipe
PVC pipe
T-piece
Ball valve
Ball valve
Ball valve
Hose tail
Hose tail
Hose tail
Hose tail
Installation instructions:
1. The parts need to be connected according to the schedule
2. Connecting the parts:
- Clean the parts that need to be connected with
cloth and the cleaner
- Glue both parts together with the PVC glue
(do not turn the parts together, just push)
- Remove excess glue with cloth
3. Connect the hoses of your pump/filter, heat pump
and pool according to the instructions below
4. Connect the hoses to the white hose tails using the
hose clamps – clamp down tightly.
User instructions:
- Disconnect the heat pump: open valve 1, close valves 2 and 3.
- Regulate the water flow to your heat pump: close valve 1, open valves 2 and 3.
When necessary you can regulate the water flow to your heat pump until the desired pressure
has been reached. If your heat pump can’t handle the flow, carefully open valve 1 to unburden
your heat pump.
Please consult the manual of your heat pump for more information and
capacities of your device.
BASIC KIT - Bypass Heat Pump
USER MANUAL
This kit is installed between your pool filter, heat pump and pool. If your installation is
equipped with a water treatment system adding products to the pool water e.g. chlorine or
salt, the bypass is placed before this installation. Please follow the instructions in this manual
and/or view the installation video’s at www.youtube.com/poolmega.
Eingang
Ausgang
Wärmepumpe
Kugelhahn 1
Kugelhahn 2
Kugelhahn 3
Eingang
Ausgang
Pool
Pumpe/Filter
Inhalt:
2 x PVC T-Stücke Ø 50mm
3 x PVC Kugelhahn Ø 50mm
4 x Edelstahl Schlauchklemme
4 x Schlauchstutzen Ø 50mm – 38/32mm
4 x PVC Rohr 10cm Ø 50mm
1 x PVC Kleber 100ml
1 x PVC Reiniger 125ml
T-Stücke
PVC Rohr
PVC Rohr
PVC Rohr
PVC Rohr
T-Stücke
Kugelhahn
Kugelhahn
Kugelhahn
Schlauchstutzen
Schlauchstutzen
Schlauchstutzen
Schlauchstutzen
Installationsanleitung:
1. Verbinden Sie die Teile entsprechend dem folgenden Plan
2. Verbinden der Teile:
- Reinigen Sie die zu verbindenden Teile mit einem
Tuch und dem Reiniger
- Kleben Sie die Teile mit dem PVC-Kleber
(lt. Herstellerangaben) zusammen (die Teile
werden nur gesteckt, nicht gedreht)
- Entfernen Sie überschüssigen Kleber mit dem Tuch
3. Verbinden Sie die Schläuche von Pumpe/Filter, Wärme-
pumpe und Pool entsprechend nachstehender Abbildung.
4. Verbinden Sie die Schläuche mit Hilfe der Schlauchklemmen
mit den weißen Schlauchstutzen und schrauben Sie die
Klemmen gut fest.
Benutzerhinweise:
- Unterbrechen der Wärmepumpe: öffnen Sie Ventil 1, schließen Sie Ventil 2 und 3.
- Regulieren des Wasserflusses an der Wärmepumpe: schließen Sie Ventil 1 und öffnen Sie Ventil 2 und 3.
Bei Bedarf können Sie den Wasserfluss an Ihre Wärmepumpe regeln, bis der gewünschte Druck erreicht ist.
Wenn Ihre Wärmepumpe den Fluss nicht bewältigen kann, öffnen Sie vorsichtig Ventil 1, um Ihre Wärmepumpe
zu entlasten.
Bitte sehen Sie für mehr Informationen und die Leistung Ihres Geräts im Handbuch Ihrer
Wärmepumpe nach.
BASISSET - Wärmepumpen-
überbrückung ANWENDERHANDBUCH
Dieses Set wird zwischen Ihrem Poolfilter, Wärmepumpe und Pool installiert. Wenn Ihre Anlage mit
einem Wasseraufbereitungssystem (Meß-Regel- und Dosiertechnik) ausgestattet ist, wird die Über-
brückung vor dieser Installation montiert. Bitte folgen Sie den Anleitungen in diesem Handbuch
und/oder schauen Sie sich das Installationsvideo unter www.youtube.com/poolmega an.
DE
EN