manualshive.com logo in svg

HydraMaster Steamatic 8800 TMU, Руководство пользователя, Страница: 85 / 148

Поделиться
Скачать
HydraMaster Steamatic 8800 TMU Скачать руководство пользователя страница 85

8-3 - Systems Troubleshooting

Steamatic 8800 TMU

CHemICal SyStem

System will not prime

1. 

1.1. The check valves in 
chemical pump are faulty.

Remove the valves and inspect. Clean or replace as 
necessary.

1.2. The chemical pump 
diaphragm is faulty.

Remove and inspect. Replace as necessary.

1.3. The check valve in high 
pressure pump is faulty (piston 
to which chemical pump is 
attached).

Remove  the  valve  and  inspect.  Clean  or  replace  as 
necessary.

1.4. The filter on feed line in 

chemical jug is clogged.

Inspect and clean.

1.5. The feed line from 
chemical jug is loose, pinched 
or damaged.

Inspect and repair.

1.6. The chemical selector 
valve is faulty.

Inspect the valve for leaks between ports. Replace as 
necessary.

Chemical flow is unstable or low

2. 

2.1. Air is in the lines

Check that all fittings and connections are tight and in 

good condition. Repair or replace as necessary.

2.2. The filter screen in the 

chemical jug is partially 
obstructed.

Inspect and clean.

2.3. The chemical selector 
valve is faulty.

Inspect the valve for leaks between ports. Replace as 
necessary.

2.4. The chemical metering 
valve is faulty.

Remove  and  inspect  the  valve.  Clean  or  replace  as 
necessary.

2.5. The high pressure check 
valve is faulty.

Remove  and  inspect  the  valve.  Clean  or  replace  as 
necessary.

Chemical is present in water box

3. 

3.1. The chemical pump 
diaphragm is faulty.

Remove and inspect the chemical pump diaphragm. 
Replace as necessary.

3.2. The high pressure check 
valve is faulty.

Remove and inspect the valve. Clean or replace as 
necessary.

Содержание Steamatic 8800 TMU





















































































































































Отзывы:

Нет отзывов