HydraMaster Steamatic 8800 TMU Скачать руководство пользователя | Manualshive

Страница: 59 / 148

background image

5-17 - Machine Maintenance

Steamatic 8800 TMU

VaCuum SyStem maIntenanCe

The vacuum pump in this machine is commonly referred to as a “rotary positive
displacement blower” or “blower” for short. The performance and life of the truckmount is
greatly dependent on the care and proper maintenance it receives. The manual for the
blower has been included. Review the manual for a better understanding of this piece of
machinery.

To protect the blower from overloading and damaging itself, there is a vacuum relief
system installed on the vacuum tank. When the vacuum tank inlet is completely
sealed off a maximum of 12” Hg will be attained.

Solid objects entering the blower will cause serious damage to the internal
components of the blower. extreme caution should be used when the truckmount is
being run for test purposes with the inlet to the blower open to the atmosphere.

foam passing through the blower can lead to serious problems with the truckmount.
It is important to keep the vacuum tank free of foam. The tank is protected from

overflowing by a float kill switch; however, this switch is not activated by foam.

daily

At the end of each day the internal components of the blower need to be lubricated. This
helps to prevent rust deposits and prolongs the life of the truckmount.

To lubricate the blower:

Allow the unit to run for a few minutes with the vacuum hose disconnected in order

1.

to remove moisture from the blower.
Cap off the inlet(s) to the vacuum tank.

2.

Spray a the manufacturer-recommended spray lubricant into the “bloWeR lUbe

3.

PoRT” for about 5 to 10 seconds while the unit is running.
Uncap the inlet(s) and run the unit for another minute to allow the blower to cool

4.

down.

periodically

Change the oil in both ends of the blower after the initial 100 hours of use. The oil is to be
changed each 500 hours of use thereafter.

«
...
57
58
59
60
61
...
»

Содержание Steamatic 8800 TMU





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Steamatic 8800 TMU

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: Parker Страницы: 54

Бренд: Canta Страницы: 2

Бренд: SALUDA MEDICAL Страницы: 61

Бренд: Halyard Страницы: 88

Бренд: HALDER Страницы: 2

Бренд: Hällde Страницы: 40

Бренд: Hällde Страницы: 6

The Wave Transformer

Бренд: EarthQuaker Devices Страницы: 21

Бренд: Jacobsen Страницы: 20

Бренд: National Instruments Страницы: 10

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды