HydraMaster Steamatic 8800 TMU Скачать руководство пользователя

Страница: 42 / 148

Operating Instructions

4-6

Steamatic 8800 TMU

SHut doWn proCedure

flush clean water through the chemical system for 10 seconds. Turn the “CHeMICAl

SeleCTIoN VAlVe” to “off.”
Cool the truckmount down by turning the “PUMP ClUTCH” switch to “PUMP oN

- No HeAT”. Spray the cleaning wand into the vacuum hose for 3-5 minutes. The

chemical should now be flushed from the truckmount, hoses and cleaning tool.

Remove the vacuum hose.

lubricate the blower to prevent it from rusting internally.

Allow the unit to run for a few minutes with the vacuum hose disconnected in

order to remove moisture from the blower.
Cap off the inlet(s) to the vacuum tank.

Spray a HydraMaster-recommended spray lubricant into the “bloWeR lUbe

PoRT” for about 5 to 10 seconds while the unit is running.
Uncap the inlet(s) and run the unit for another minute to allow the blower to cool

down.

If freeze guarding is necessary, perform the procedure at this time. See the freeze

Guarding section of this owner’s Manual (see page 5-19).
Press the engine throttle switch to the “IDle” position.

Turn the ignition switch to “off.”

Drain the water box using the valve.

Drain the vacuum tank in an appropriate location.

In accordance with ePA, state and local laws, do not dispose of water into gutters,
storm drains, streams, or reservoirs.

Perform daily maintenance as specified in Section

10.

5 of this owner’s Manual.

Содержание Steamatic 8800 TMU





















































































































































Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы:

Похожие инструкции для Steamatic 8800 TMU

Бренды по названию

Популярные бренды

HydraMaster Steamatic 8800 TMU, Руководство пользователя

Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы:

Похожие инструкции для Steamatic 8800 TMU

Бренды по названию

Популярные бренды