HydraMaster Steamatic 8800 TMU Скачать руководство пользователя

Страница: 33 / 148

3-1 - Cleaning Information

Steamatic 8800 TMU

3 - Cleaning Information

The Steamatic 8800 TMU has been engineered using the latest and most sophisticated

technology available to produce the finest carpet cleaning results possible. Despite this,

it remains only a tool of the carpet cleaning trade and can produce only as a good a job
as the person operating it.

The manufacturer strongly recommends attending an Institute of Inspection, Cleaning

and Restoration Certification (IICRC) approved school as soon as possible and to always

follow the IICRC guidelines when cleaning carpets or hard surfaces.

This section describes the carpet cleaning procedure in the following areas:

Precautions

Preparing the Carpet for extraction

Rinse and Recover

overwetting

Streaking

Cleaning Tool Tips

Содержание Steamatic 8800 TMU





















































































































































Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы:

Похожие инструкции для Steamatic 8800 TMU

Бренды по названию

Популярные бренды

HydraMaster Steamatic 8800 TMU, Руководство пользователя

Результаты поиска

Содержание Steamatic 8800 TMU

Отзывы:

Похожие инструкции для Steamatic 8800 TMU

Бренды по названию

Популярные бренды