manualshive.com logo in svg

HydraMaster RX-20 700-041-006, Руководство пользователя, Страница: 49 / 52

Поделиться
Скачать
HydraMaster RX-20 700-041-006 Скачать руководство пользователя страница 49

10-1:  Troubleshooting

RX-20

10 - Troubleshooting

Low Vacuum Flow at the Cleaning Heads

1.0  

Possible Cause

Solution

1.1 Hub not sealing properly.

Replace felt seal with a lubricated one.

1.2 Restricted air flow. 

Remove hoses from the vacuum shoe and skid 
assembly, and clear them of debris.

1.3 Low vacuum flow from power.

Refer to Troubleshooting section of source 
equipment manual.

Low Water Flow at Cleaning Heads (indicated by irregular Water Temperature)

2.0  

Possible Cause

Solution

2.1 Restricted jets.

Remove jets and clear them of debris.

2.2 Clogged water strainer.

Remove water strainer and clean.

2.3 Kinked or clogged solution 
hose.

Remove hose. Repair or replace. 

2.4 Cleaning hub not properly 
threaded.

Remove cleaning hub from shaft to shaft. Clean 
and rethread onto shaft.

Water Leak at Rotary Union

3.0  

Possible Cause

Solution

3.1 foreign matter in rotary union 
seal.

dismantle rotary union. Clean. Re-assemble and 
install.

Water Leak at Valve

4.0  

Possible Cause

Solution

4.1  Ruptured  plunger  or  valve 
O-ring.

Repair or replace damaged plunger, O-ring, seal. 
Check for freeze damage.

4.2  Ruptured  plunger  or  valve 
O-ring.

Repair or replace damaged plunger, O-ring, seal. 
Check for freeze damage.

Содержание RX-20 700-041-006





















































Отзывы:

Нет отзывов