manualshive.com logo in svg

HydraMaster Chem-Dry PowerHead, Руководство пользователя

Поделиться
Скачать
HydraMaster Chem-Dry PowerHead Скачать руководство пользователя страница 49

11-1:  Limited Warranty Plan

  Harris Research, Inc. 

Chem-Dry

®

 

PowerHead

®

11 - Limited Warranty Plan

Harris Research, Inc (HRI) warrants PowerHead machines of its manufacture to be free 
from defects in material and workmanship if properly installed, maintained, and operated 
under normal conditions with competent supervision. No person, agent, representative 
or dealer is authorized to give any warranties on behalf of HRI, nor to assume for HRI 
any other liability in connection with any HRI products. This warranty shall extend to the 
original purchaser of said equipment for the periods listed below from date of installation. 
If repairs or replacements are made by the Chem-Dry Franchisee (owner) without the 
written consent of HRI, HRI’s warranty shall cease to be in effect.

Machinery, equipment and accessories furnished by Harris Research, Inc., but 
manufactured by others, are warranted only to the extent of the original manufacturer’s 

warranty to Harris Research, Inc. unless otherwise specified in the listing below.

HRI agrees, at its option, to repair at the point of shipment, or to replace without charge, 

any parts or parts of products of HRI manufacture, which within the specified warranty 

period shall be proved to HRI satisfaction to have been defective when shipped, provided 

the Chem-Dry Franchisee (owner) promptly notifies HRI, in writing, of such alleged defect. 

HRI will pay all freight and transportation charges within the United States, via normal 
ground shipping means, for replacement of parts covered under this warranty.

This warranty covers parts, as specified, and does not cover labor which may be necessary 

in completing repairs. HRI’s liability to the Chem-Dry Franchisee (owner), whether in 
contract or in tort arising out of warranties, representation, instructions, or defects from 
any cause shall be limited to repairing or replacing the defective part or parts. To qualify for 
warranty coverage, defective parts must be returned to HRI within 30 days. No warranty 
liability whatsoever shall attach to HRI unless and until HRI has received payment in full 
for the warranted machine or part.

Except as stated in this section and in the proceeding section and except as to title, there 

are no guarantees or warranties of merchantability, fitness, performance or otherwise, 

express, implied or statutory, and HRI shall have no liability for consequential, incidental 
or other damages howsoever caused.

All components not specifically referenced in the schedule below are covered under this warranty 

for a period of one (1) year, excepting those parts which are considered, by HRI, to be expendable 
in normal use, including, but not limited to paint, labels and other cosmetic parts or features.

Freezing of any water or chemical-related component will VOID all warranties on water or 
chemical related components, internal or external, of this equipment.

Содержание Chem-Dry PowerHead



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды