HydraMaster Chem-Dry PowerHead Скачать руководство пользователя страница 47

Страница: 47 / 50

10-1: Troubleshooting

Harris Research, Inc.

Chem-Dry

PowerHead

10 - Troubleshooting

1.0 LOW VACUUM FLOW AT THE CLEANING HEADS

Possible Cause

Solution

1.1

Hub not sealing properly.

Replace felt seal with a lubricated one.

1.2

Restricted air flow.

Remove cleaning head and clear all vacuum lines
and heads of debris.

1.3

Low vacuum flow from

power

Refer to the Troubleshooting section of the source
equipment manual.

2.0 LOW WATER FLOW AT CLEANING HEADS (INDICATED BY IRREGULAR WATER
TEMPERATURE)

Possible Cause

Solution

2.1

Restricted jets.

Remove jets and clear them of debris.

2.2. Kinked or clogged solution

hose

Remove hose. Repair or replace.

2.3

Cleaning hub not properly
threaded

Remove cleaning hub from shaft. to shaft. Clean and
rethread onto shaft.

3.0 WATER LEAK AT ROTARY UNION

Possible Cause

Solution

3.1

Foreign matter in rotary
union seal.

Dismantle rotary union. Clean. Re-assemble and
install.

4.0 WATER LEAK AT VALVE

Possible Cause

Solution

4.1

Ruptured plunger or
valve O-ring.

Repair or replace damaged plunger, O-ring, seal.
Check for freeze damage.

5.0 LOSS OF OIL FROM GEAR BOX

Possible Cause

Solution

5.1

Loose or ruptured oil
seal.

Replace damaged oil seal. Refill gear box with oil.

Содержание Chem-Dry PowerHead



















































Результаты поиска

Содержание Chem-Dry PowerHead

Отзывы:

Бренды по названию

Популярные бренды

HydraMaster Chem-Dry PowerHead, Руководство пользователя

Результаты поиска

Содержание Chem-Dry PowerHead

Отзывы:

Бренды по названию

Популярные бренды