manualshive.com logo in svg

HydraMaster Chem-Dry PowerHead, Руководство пользователя

Поделиться
Скачать
HydraMaster Chem-Dry PowerHead Скачать руководство пользователя страница 13

  Harris Research, Inc.  

3-1: Assembly Instructions

Chem-Dry

®

 

PowerHead

®

3 - Assembly Instructions

To prepare your machine for use, follow these instructions: 

1.  Remove the machine from the packaging.
2.  Inspect the machine carefully for any damage that may have occurred during 

shipping. 

3.  Check the gear box lubricant level (see page 6-3 of this Owner’s Manual). 
4.  Attach the cleaning head to the base. 

a.  Lean the machine back and rest it on the handle.
b.  Thread the star assembly (cleaning head) onto the exposed shaft in a 

counterclockwise direction. 

Remove the solid shipping plug from the top of the gear box and replace it with 
the vented plug provided before operating the machine (see Figure 3-1 and 
Figure 3-2). Failure to follow these directions may result in damage to the gear 
box and seal.

5.  Re-attach the cover onto the PowerHead.

Your machine is now ready to operate.

Figure 3-2.  Base without Cover

Shipping 

Plug

Figure 3-1.   Base with Cover

Gear Box 

Cover

Two 8 x 1/2” 

Screws

Содержание Chem-Dry PowerHead



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды