HydraMaster CDS 4.6 Скачать руководство пользователя страница 29

Страница: 29 / 126

operating Instructions: 3-6

▬

For Ford Vans

▬

The ford 3 Speed Throttle Controller must meet certain “Chassis Ready” conditions to

elevate the engine rpm, which are:

Parking Brake is set.

Gear shift is in “Park”.

foot is off Service Brake (brake pedal).

foot is off Accelerator Pedal.

Vehicle is stationary (no speed).

Brake light circuit is functional.

engine coolant is above 140° f.

Transmission oil Temperature is below 240° f.

Maximum Catalytic Temperature has not been met.

SeIC (Stationary elevated Idle Control)* will be terminated by a safety condition violation.

for instance, the SeIC will be terminated if the service brake is depressed at any time

during its operation.
The 3 lights on the Throttle Control assembly indicate the following conditions (refer to

figure 3-2 and Table 3-2):

ReD lIGHT: the Throttle Control assembly is receiving power from the vehicle, but

the SeIC process has not been initiated.

yelloW lIGHT: all the “Chassis Ready” conditions have been met and the SeIC

process has been initiated.

GReeN lIGHT: the Throttle Control assembly is receiving power from the CDS and

the SeIC process is operational.

Location of 3 Lights on Throttle Control Assembly

Figure 3-2.

* SeIC is ford’s onboard computer throttle control strategy.

Содержание CDS 4.6































































































































Результаты поиска

Содержание CDS 4.6

Отзывы:

HydraMaster CDS 4.6, Руководство пользователя, Страница: 29 / 126

Результаты поиска

Содержание CDS 4.6

Отзывы: