HydraMaster CDS 4.6 Скачать руководство пользователя страница 105

Страница: 105 / 126

8-1: Vacuum Blower System

8 - Vacuum Blower System

This section of the manual covers the CDS’ vacuum blower system and includes

information on:

Vacuum Tank Inlet filter

Vacuum Blower lubrication

Vacuum Blower Troubleshooting

The vacuum blower, featuring tri-lobe rotors, is designed

for maximum positive displacement and manufactured

using special porting technology to significantly reduce

noise.

lubrication for both the gear end and drive end of the

blower is provided by full oil splash. unlike grease

lubrication, oil-splash lubrication provides for longer bearing and seal life through improved

heat dissipation.

At the gear end, the timing gear teeth are lubricated by submersion in oil with the gear teeth

serving as oil slingers. At the drive end, the bearings are also lubricated by submersion in

oil with oil slingers attached on the shafts.

The performance and life of the vacuum blower is greatly dependent on the care and

proper maintenance it receives.

Because of the close tolerances between the 3 lobes and housing of the vacuum blower,

solid objects entering the inlet will damage the internal lobes, gears, bearings or drive

system.

To prevent this from happening, a stainless steel filter screen has been placed at the

vacuum blower intake inside the vacuum recovery tank. This stainless steel filter system

should be removed for cleaning on a daily basis.

use caution when the CDS is being run for test purposes and the vacuum inlet is open.

unregulated vacuum may cause injury if body parts come in contact with the open vacuum

inlet.

Содержание CDS 4.6































































































































Результаты поиска

Содержание CDS 4.6

Отзывы:

HydraMaster CDS 4.6, Руководство пользователя, Страница: 105 / 126

Результаты поиска

Содержание CDS 4.6

Отзывы: