HydraMaster BoxxerXL Скачать руководство пользователя

Страница: 62 / 144

Machine Maintenance: 5-16

VaCUUM SySteM MaIntenanCe

The vacuum pump in this machine is commonly referred to as a “rotary positive

displacement blower” or “blower” for short. The performance and life of the truckmount is

greatly dependent on the care and proper maintenance it receives. The manual for the

blower has been included. Review the manual for a better understanding of this piece of

machinery.

To protect the blower from overloading and damaging itself, there is a vacuum relief

system installed on the vacuum tank. When the vacuum tank inlet is completely

sealed off a maximum of 12” Hg will be attained.

Solid objects entering the blower will cause serious damage to the internal

components of the blower. extreme caution should be used when the truckmount is

being run for test purposes with the inlet to the blower open to the atmosphere.

foam passing through the blower can lead to serious problems with the truckmount.

It is important to keep the vacuum tank free of foam. The tank is protected from

overflowing by a float kill switch; however, this switch is not activated by foam.

Daily

At the end of each day the internal components of the blower need to be lubricated. This

helps to prevent rust deposits and prolongs the life of the truckmount.

To lubricate the blower:

1. Allow the unit to run for a few minutes with the vacuum hose disconnected in order

to remove moisture from the blower.

2. Cap off the inlet(s) to the vacuum tank.
3. Spray a HydraMaster-recommended spray lubricant into the Blower Lube Port for

about 5 to 10 seconds while the unit is running.

4. uncap the inlet(s) and run the unit for another minute to allow the blower to cool

down.

periodically

Change the oil in both ends of the blower after the initial 100 hours of use. The oil is to be

changed each 500 hours of use thereafter.

Содержание BoxxerXL

















































































































































Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды

HydraMaster BoxxerXL, Руководство пользователя

Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды