HydraMaster BoxxerXL Скачать руководство пользователя | Manualshive

Страница: 50 / 144

background image

Machine Maintenance: 5-4

OVeraLL MaCHIne MaIntenanCe

Maintenance, troubleshooting and repair are much easier tasks to accomplish on a clean

truckmount. Regular cleaning of the truckmount offers the user an opportunity to visually

inspect all facets of the truckmount and spot potential problems before they occur. In

addition to the operational maintenance the following “housekeeping” duties should be

performed.

after each job

•

Check the recovery tank and the recovery tank filters. Empty and clean as

necessary.

Daily

•  Wipe the truckmount down thoroughly with a damp cloth.
•  Wipe down the vacuum and high pressure hoses as needed.
•  Inspect and clean the vacuum slot on the cleaning wand.
•  Check the wand head for sharp edges that could tear carpet. file down as needed.
•  Clean the wand to maintain original appearance.
•  Visually inspect the hoses for abrasions, cuts, etc. Repair or replace as needed.

Weekly

• empty the chemical container. Wash out thoroughly to remove any chemical buildup.
• Inspect the chemical feed line strainer and use solution of equal parts white vinegar

and water to remove any chemical buildup.

• Thoroughly clean the wand and inspect for clogged jets, debris in vacuum slot and

leaking fittings at valve.

• Thoroughly clean the vacuum and high pressure hoses including quick releases and

cuffs.

«
...
48
49
50
51
52
...
»

Содержание BoxxerXL

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для BoxxerXL

Бренд: Paradox Страницы: 72

Бренд: Zoeller Страницы: 4

Бренд: Mallory Страницы: 7

Бренд: Neo Car Audio Страницы: 19

Бренд: 2easy Страницы: 12

Бренд: 2easy Страницы: 30

Бренд: Cadillac Страницы: 4

Бренд: Cadillac Страницы: 107

Бренд: CALEFFI Страницы: 8

Бренд: Caliber Страницы: 22

Бренд: Lavor Страницы: 108

Бренд: Ecco Страницы: 2

Бренд: Jasic Страницы: 30

Бренд: vacuubrand Страницы: 24

Бренд: Quantum Страницы: 97

Бренд: Wayne Страницы: 8

Бренд: Wayne Страницы: 20

Бренд: Wayne Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды