HydraMaster BoxxerXL Скачать руководство пользователя страница 31

Страница: 31 / 144

2-5: Installation Information

SettIng Up tHe BOXXer XL

Prior to operating the Boxxer XL, follow these steps:

1. Adjust the vacuum relief located on the recovery tank by capping all the vacuum

inlets. The machine should be set to 12” Hg maximum.

Setting the vacuum level higher than the recommended value can result in an

increased risk of serious component damage.

The Boxxer XL is shipped from the factory with antifreeze added to the solution system.

Recover this antifreeze and dispose of the recovered antifreeze as stated in the local laws

and regulations.

KeeP ANTIfReeZe OuT Of ReACH Of CHILDReN AND ANIMALS. Drinking

antifreeze can cause death.

If required, dispose of antifreeze at facilities licensed to accept household

hazardous waste. If permitted, dispose of antifreeze in sanitary sewer systems.

Do not pour antifreeze into storm sewers, septic systems, or onto the ground.

Doing so causes health and environmental dangers.

ensure the antifreeze is completely drained from the solution system. If any

antifreeze remains in the system, it could damage machine components and

damage fabric.

Содержание BoxxerXL

















































































































































Результаты поиска

Содержание BoxxerXL

Отзывы:

Бренды по названию

Популярные бренды

HydraMaster BoxxerXL, Руководство пользователя

Результаты поиска

Содержание BoxxerXL

Отзывы:

Бренды по названию

Популярные бренды