manualshive.com logo in svg

HydraMaster Boxxer 423s, Руководство пользователя

Поделиться
Скачать
HydraMaster Boxxer 423s Скачать руководство пользователя страница 18

2-5:  Installation Information

   Installation Information:  2-4

A sudden or crash stop will cause the machine to rocket forward if not properly 
secured. To prevent serious personal injury, ensure that the Boxxer 423s is well 

secured to the floor of the vehicle with the hardware supplied. Protect yourself 

and the machine. 

HydraMaster strongly recommends that the exhaust from the front of the machine 
be vented down under the truck to prevent carbon monoxide from entering the 
job site. 

Always park the truck so the exhaust is blowing away from the job 

site

.

Never operate this machine with a portable gas can inside the truck. Doing so 

increases the risk of a fire or explosion.

Mount a fire extinguisher just inside the rear or side door for emergencies.

Do not use a portable propane tank inside of the truck or van. It is dangerous and 
illegal in most states.

Transporting any vented fuel container that presently holds or has ever held a 

flammable liquid in a vehicle containing the Boxxer 423s is strictly forbidden by 

HydraMaster Corporation and by federal and state regulation.

The engine exhaust from this product contains chemicals known to the State of 
California to cause cancer, birth defects or other reproductive harm.

SETTING UP THE BOXXER 423S

Prior to operating the Boxxer 423s, follow these steps:

1.  Adjust the vacuum relief located on the recovery tank by capping all the vacuum   

inlets. The machine should be set to 12” Hg maximum.

Setting the vacuum level higher than the recommended value can result in an 
increased risk of serious component damage.

The Boxxer 423s is shipped from the factory with antifreeze added to the solution system. 

Recover this antifreeze and dispose of the recovered antifreeze as stated in the local laws 
and regulations.

KEEP ANTIFREEZE OUT OF REACH OF CHILDREN AND ANIMALS. Drinking 
antifreeze can cause death.

If required, dispose of antifreeze at facilities licensed to accept household 
hazardous waste. If permitted, dispose of antifreeze in sanitary sewer systems. 
Do not pour antifreeze into storm sewers, septic systems, or onto the ground. 
Doing so causes health and environmental dangers.

Ensure the antifreeze is completely drained from the solution system. If any 
antifreeze remains in the system, it could damage machine components and 
damage fabric.

 

Содержание Boxxer 423s





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды