background image

HydraMaster Corporation

Page 4-2: Machine Maintenance

Boxxer 421

WEEKLY (cont.):

• Check pump pulleys.
• Check high pressure water lines for wear or chafing.
• Check all nuts and bolts. Tighten as needed.
• Inspect vacuum relief valve.  Clean and lubricate as necessary.
• Clean vacuum tank thoroughly with high pressure washer.
• Check wiring for chafing.
• Flush water and chemical system with 50/50 white vinegar solution.
• Change engine oil (every 50 hrs.).

MONTHLY:

• Change oil filter (every other oil change).
• Check engine air cleaner filter.  Clean as necessary.
• Remove pressure bypass valve piston plate.  Grease plate.  Reinstall.
• Check water level in battery.  Clean connections as needed.

QUARTERLY:

• Check fuel lines.
• Clean and gap spark plugs.
• Check drive coupler for cracks or wear.  Replace as necessary.
• Change oil in blower.
• Change pump oil.
• Grease blower bearing fittings.

500 HOURS:

• Replace plugs in the drive coupling, between the engine and the blower..

Содержание Boxxer 421




















































































































































































Отзывы: