Hydac FCU 1310 Скачать руководство пользователя страница 64

Страница: 64 / 148

7 | Operation

HYDAC FILTER SYSTEMS GMBH

64 / 148

BeWa FCU1310 3371346g en-us lq

7.2 Operating/Setting measuring menu

Settings in the measuring menu are possible during operation.

Selection

To do

Start the measuring menu

Press the

button.

Exit the measuring menu with-
out saving

Scroll to

and

use the

button for con-

firmation or wait 30 seconds
without actuating a button.

Save and exit the measuring
menu

Scroll to

and con-

firm with the

button.

You are scrolling through the measuring menu:

For details, see:

RECORD – Record measurements
[

}

65]

MEMORY – Displaying free mea-
surement report memory [

}

68]

ED.MPNT – Change name of mea-
surement point [

}

69]

TP.UNIT - Set temperature unit
[

SAVE – Saving settings / data
[

}

74]

Tab. 13:

Measuring Menu

Press the

button to switch to a sub-menu.

Содержание FCU 1310





















































































































































Результаты поиска

Содержание FCU 1310

Отзывы:

Похожие инструкции для FCU 1310

Бренды по названию

Популярные бренды

Hydac FCU 1310, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание FCU 1310

Отзывы:

Похожие инструкции для FCU 1310

Бренды по названию

Популярные бренды