Hydac CSI-B-1 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 36

background image

CSI-B-1

CSI-B-1 is detected by the PC

CSI-B-1 is detected by the PC

The PC detects the CSI-B-1 after the following steps have been carried out:

-

USB driver is installed

-

CSI-B-1 is connected with the PC via a USB cable

-

the PC is switched on

-

the CSI-B-1 is equipped with voltage

You will receive the following message only after the first time the CSI-B-1 is
connected:

New hardware found

Installation ....

This completes the installation of the CSI-B-1.

Run the Windows DeviceManager as follows in order to determine the COM
interface at which the CSI-B-1 is now located.

Settings -> System Control -> System -> Hardware -> DeviceManager

DeviceManager

!

If the CSI-B-1 has been detected by the system, then this will be identified in the
DeviceManager with the corresponding COM interface (here: COM9).

Please make a note of this COM interface for yourself. This information will be
needed again when the HyperTerminal is opened.

HYDAC FILTER SYSTEMS GMBH

en(us)

Page 18 / 36

BeWa CSI-B-1 3424452b 2012-04-20 en-us.doc

2012-04-20

«
...
16
17
18
19
20
...
»

Содержание CSI-B-1





































Отзывы:

Нет отзывов

Похожие инструкции для CSI-B-1

Бренд: MAHLE Страницы: 21

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: Rapala Страницы: 14

Бренд: S.R.Smith Страницы: 43

Бренд: quadient Страницы: 188

Бренд: Radarsign Страницы: 16

Бренд: Raytec Страницы: 60

Бренд: S.R.Smith Страницы: 8

Бренд: S.R.Smith Страницы: 23

NavBoard ZipFlip

Бренд: S&S Precision Страницы: 6

Бренд: GE Страницы: 18

Бренд: Ideal Heating Страницы: 16

Бренд: Aveo Engineering Страницы: 16

Бренд: Hedson Страницы: 32

Бренд: JLG Страницы: 165

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды