HYDAC FILTER SYSTEMS OLFCM 10/15 Скачать руководство пользователя страница 51

Страница: 51 / 80

HYDAC FILTER SYSTEMS GMBH

Rectifying malfunctions | 7

MoWa OLFCM 3573893a en-us lq

51 / 80

Malfunction

Cause(s)

Rectification

the circulation of
the fluid within
the pump (pres-
sure relief valve
opened) and
normal pump op-
eration has then
started.

Leakage at the
filter bowl/filter
cartridge

The drain plug at
the filter housing
or the housing
clamps at the fil-
ter bowl are
loose.

Tighten the nuts
of the housing
clamps to the re-
quired torque.

In the case of a
Spin-On filter
cartridge, tighten
it fully. If neces-
sary, replace the
filter cartridge
seal.

Tab. 10:

Error/cause/rectification

Malfunction

Cause(s)

Rectification

The running
noise of the mo-
tor-pump assem-
bly becomes
substantially
louder.

The protective
screen is
clogged.

Clean the pro-
tective screen.

The pump is not
sucking or suck-
ing badly.

There is no oil in
the pump.

Fill the pump via
the suction hose.

Содержание OLFCM 10/15

















































































Результаты поиска

Содержание OLFCM 10/15

Отзывы:

HYDAC FILTER SYSTEMS OLFCM 10/15, Инструкция по установке и обслуживанию, Страница: 51 / 80

Результаты поиска

Содержание OLFCM 10/15

Отзывы: