HYDAC FILTER SYSTEMS OLFCM 10/15 Скачать руководство пользователя страница 3

Страница: 3 / 80

HYDAC FILTER SYSTEMS GMBH

Table of Contents

MoWa OLFCM 3573893a en-us lq

iii

Mounting/installing .................................................................................................. 36

5.1

Fastening/mounting the filter unit ................................................................... 36

5.2

Avoiding siphoning ......................................................................................... 39

5.3

Observing/calculating pressure loss .............................................................. 40

5.4

Measure or display dynamic pressure / differential pressure......................... 42

5.5

Connecting the (IN) suction port .................................................................... 43

5.6

Connecting the pressure port (OUT).............................................................. 44

5.7

Electrically connecting the electric motor ....................................................... 44

5.8

Connecting the electric clogging indicator (optional)...................................... 46

5.9

Connecting/supplying the ContaminationSensor with voltage ....................... 46

5.10 Connecting the AquaSensor to the monitoring unit (optional)........................ 46

5.11 Commissioning the filter unit .......................................................................... 46

5.12 Checking the installation ................................................................................ 48

Operation ................................................................................................................ 49

6.1

Observing the optical clogging indicator (optional) ........................................ 49

Rectifying malfunctions ........................................................................................... 50

Performing maintenance ......................................................................................... 52

8.1

Maintenance table.......................................................................................... 53

8.2

Resetting the VM x BM.x visual clogging indicator ........................................ 53

8.3

Changing the filter element - Toploader......................................................... 54

8.4

Changing the protective screen ..................................................................... 59

Appendix ................................................................................................................. 61

9.1

Finding spare parts / accessories .................................................................. 61

9.1.1

Spare parts - Toploader..................................................................... 63

9.1.2

Diagram of spare part - OLFCM-x/xx-T-... Toploader........................ 64

9.1.3

Accessories - Tank Connection Kit OLF-5-TAK ................................ 65

9.2

Clogging indicators - technical data ............................................................... 66

9.2.1

Differential pressure indicator, visual – VM x B.x .............................. 66

9.2.2

Differential pressure indicator, visual – VM x BM.x ........................... 68

Содержание OLFCM 10/15

















































































Результаты поиска

Содержание OLFCM 10/15

Отзывы:

HYDAC FILTER SYSTEMS OLFCM 10/15, Инструкция по установке и обслуживанию, Страница: 3 / 80

Результаты поиска

Содержание OLFCM 10/15

Отзывы: