HYDAC FILTER SYSTEMS OLFCM 10/15 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 80

HYDAC FILTER SYSTEMS OLFCM 10/15 Скачать руководство пользователя страница 18

3 | Filter unit/filter housing over-view

HYDAC FILTER SYSTEMS GMBH

18 / 80

MoWa OLFCM 3573893a en-us lq

3 Filter unit/filter housing over-view

The filter units of the OLF-5 and OLF-10 series are used for
the fine filtration of hydraulic oils in bypass flow. The series has
many versions e.g. with or without the motor-pump unit, ele-
ment removal to the top or bottom, tank installation variants,
optionally with integrated Condition Monitoring for the determi-
nation of fluid purity and water content etc.

Depending on the version, flow rates up to 15 l/min and vis-
cosities up to 7,000 mm²/s can be supported. Additionally, the
use of filter elements with up to a 2 µm absolute filtration rating
along with a dust holding capacity of up to 200 g (N5) or 500 g
(N10)

The

filter elements used are characterized by:

- An especially high dust holding capacity
- Environmentally friendly disposal (incinerable) and
- Water retention (optional).

Filter units
OLF-5/15-…/
OLF-10/15-…

The filter units of the OLF-5/15-… / OLF-10/15-… "Hydraulic
series" were developed especially for applications in hydraulic
systems with a tank volume of up to ≈ 2,000 liters. This filter
unit functions with a flow rate of between 5 ... 15 l/min.

«
...
16
17
18
19
20
...
»

Содержание OLFCM 10/15

















































































Отзывы:

Нет отзывов