HYDAC FILTER SYSTEMS CTM-EF 3 3 Series Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 64

background image

HYDAC FILTER SYSTEMS GMBH

Operation | 6

BeWa CTM-EF3x3x 4436386 en-us lq

39 / 64

6.3 Cascading filter membranes/replacing filter

membranes

Depending on the filter membrane holder, the procedure for cascading or the
replacement of the filter membranes varies. In the following, you will find how
you should handle different filter membrane holders.

6.3.1 Creating cascades

Cascade the filter membranes in the filter membrane holder according to the fol-
lowing illustration (example: filter membrane holder with quick fastener)

Fig. 12:

Cascading the

filter membrane holder

Item

Tool

1

Coupling

2

Hose connection

3

Diffuser

The diffuser - allows for the even distribution of the test liquid

over the entire surface of the filter membrane.

4

Upper part of the filter membrane holder

5.1

Filter membrane, 100 µm

5.2

Filter membrane, 20 µm

5.3

Filter membrane, 5 µm

6

Supporting sieve

7

Intermediate ring

8

The lower part of the filter membrane holder with a hose con-

nection

A

Cascade - coarse

B

Cascade - medium

C

Cascade - fine

Tab. 11: Cascading the filter membrane holder

The design presses the filter membrane in the lower part (8) of the filter mem-
brane holder function-tight to the upper part (4).

«
...
37
38
39
40
41
...
»

Содержание CTM-EF 3 3 Series

































































Отзывы:

Нет отзывов

Похожие инструкции для CTM-EF 3 3 Series

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

Бренд: Ebyte Страницы: 35

Бренд: IAI Страницы: 5

Z3-DM8107-SDI-RPS

Бренд: Z3 Technology Страницы: 73

Бренд: Z-Wave Страницы: 14

Бренд: Z-Wave.Me Страницы: 4

Бренд: Vag Страницы: 15

Бренд: oventrop Страницы: 64

SmarTemp Control fx

Бренд: Webasto Страницы: 8

Бренд: Nibe Страницы: 92

Бренд: jbc Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды