HYDAC FILTER SYSTEMS CTM-EF 3 3 Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 64

background image

5 | Setting up/assembling/commissioning

HYDAC FILTER SYSTEMS GMBH

32 / 64

BeWa CTM-EF3x3x 4436386 en-us lq

5.2 Electrical connection

ü

The extraction unit is supplied ready for connection with a power plug fit-

ted.

1. Before plugging in the power plug, please compare that the voltage from

the available network corresponds to that specified on the name plate of

the extraction unit.

2. Plug the power plug only into a power outlet with a ground connection.

O

The extraction unit is electrically connected to the supply network.

5.3 Connecting the compressed air supply

The extraction unit requires a compressed air connection for operation. The
compressed air requirements can be found in Chapter

Technical Data [

1. Connect the quick-action coupling of the compressed air supply to the

standard connection nipple of the low-pressure series DN 7.2 on the ex-

traction unit.

2. Open the shut-off valves that may be present in the supply line.

3. Check the state and the setting of the maintenance unit in the supply line.

O

The pressure port is connected.

5.4 Connecting the CTM-EF extraction unit to

the GTM-SC supply module

So that both modules work together, the electrical as well as the hydraulic con-
nection is required.

Screw wrench

= 22 mm

Attach the male connector to the control unit and also attach the connection
hoses of the CTM-EF3xxx to the CTM-SC as shown in the following illustration.

«
...
30
31
32
33
34
...
»

Содержание CTM-EF 3 3 Series

































































Отзывы:

Нет отзывов

Похожие инструкции для CTM-EF 3 3 Series

Бренд: JDS Uniphase Страницы: 27

Бренд: Danfoss Страницы: 20

Бренд: OEG Страницы: 168

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: Samson Страницы: 40

Бренд: Laird Страницы: 38

Бренд: Laird Страницы: 5

Бренд: U-Prox Страницы: 3

Бренд: Valcom Страницы: 6

FSDrive-MV1000 Series

Бренд: YASKAWA Страницы: 260

Бренд: YASKAWA Страницы: 114

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 152

Бренд: YASKAWA Страницы: 66

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды