manualshive.com logo in svg

Hycontrol VF05, Руководство пользователя и программирования

Поделиться
Скачать
Hycontrol VF05 Скачать руководство пользователя страница 12

 

 

12 / 27 

4.3.1.

 

BUS (HART

®

) communication 

 

The output of the device can be used in two ways: 

1. Current loop output and HART

®

  

2. Passive, HART

®

 protocol 

The HyView program supports the use of both modes. 
According to the Rosemount Standard, HART

®

 communication can be used as a point-to-point connection between VF05 

as a “slave” and a HART

®

 

“master”.

 

There are two modes of communication: 

•

 

If the device (HART

®

 

short address 0) is set to current loop transmission (4…20 mA), 

only one device can be in the HART

®

 communication loop 

•

 

For multidrop operation (4mA), several devices (max. 15) can be connected to one HART

®

 communication loop. In this case, a short address other than 0 

must be set for the device. 

 

 

 

 

 

4.4.

 

S

WITCHING 

O

N AND 

C

OMMISSIONING

 

 

The VF05 two-wire device is supplied by HYCONTROL with the technical specifications requested by the customer, so it is ready for operation immediately after 
installation and wiring up. 
Measuring starts less than 20 seconds after switching on. 

Attention! The initial current consumption of the device is 3.5 mA right after switching on!

 If there is 

a change in the installation data due to shortening a cable probe, the set parameters must be changed according to the application before starting the measurement. 

 

4.5.

 

A

VAILABLE 

U

SER 

I

NTERFACES

 

 

The instrument can be programmed by using the following devices / accessories: 

VGF-DISPLAY display unit 

Ordered separately. See ”5.2. Programming with the 

VGF-DISPLAY 

display unit.”

 

Hyview software (PC needed) 

Available as download 

HART

®

 Microlink USB modem  

Ordered separately. See ”5.1. Programming with 

HyView

”

  

 

Содержание VF05




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды