Huvema HU 32 SUPER VARIO, Руководство пользователя

Страница: 9 / 24

9
CHANGES AND T YPING ERRORS RESERVED CHANGES AND T YPING ERRORS RESERVED CHANGES AND T YPING ERRORS RESERVED
You can position the vice by loosening the set screw (figure 14).
Tighten the set srew when the vice is in the correct position.
7.5 D
epTh aDjUsTmenT
To prevent the drill or tap from going too deep into the work piece,
you can set the feeding limit by adjusting the position of the feed depth
adjustment (A, figure 15).
7.6 s
peeD
s
elecTion
Drill
diameter
(mm)
Material
Cast Iron Steel Iron Aluminium Alloy Copper
Drilling Tapping Drilling Tapping Drilling Tapping Drilling Tapping Drilling Tapping
2 4780 2390 1275 635 3980 1910 7960 3980 4460 2230
3 3185 1590 850 425 2650 1275 5310 2655 2970 1485
4 2390 1195 640 320 1990 955 3980 1990 2230 1115
5 1910 955 510 255 1590 765 3185 1590 1785 890
6 1590 795 425 210 1330 640 2655 1330 1485 745
7 1365 680 365 180 1140 545 2275 1140 1275 635
8 1195 600 320 160 995 480 1990 995 1115 555
9 1060 530 285 140 885 425 1770 885 990 495
10 955 480 255 125 800 380 1590 800 890 445
11 870 435 230 115 725 350 1450 725 910 405
12 795 400 210 105 665 320 1330 665 745 370
13 735 365 195 100 610 295 1225 610 685 340
14 680 340 180 90 570 270 1135 570 635 320
15 640 320 170 85 530 255 1060 530 600 300
16 600 300 160 80 500 240 995 500 560 280
17 560 280 150 75 470 225 935 470 525 260
18 530 265 140 70 440 210 885 440 495 250
19 500 250 135 67 420 200 835 420 470 235
20 480 240 130 65 400 190 795 400 445 225
25 380 190 100 50 320 155 640 320 355 180
30 320 160 85 45 265 130 530 265 300 150
40 240 120 65 30 200 95 400 200 225 110
Figure 14
6.Please open water outlet valve and adjust a proper water outlet volume after power supplying. Fig 18
11
7.Adjust work table position
(1)Firstly, loose the clamp handle in left hand
(Figure 19)
(2)Then swing the table handle to properly position.
(Figure 20)
(3)Finally tight the clamp handle.
(Figure 19)
8.Pulley Cover Open and Close Method
(1)Open iron cover — hold the handle of left iron cover (Figure 21A) and push upward to the highest point and then release
slightly; use locator (Figure 22 B) to fix the iron cover as open state.
Figure 14 Figure 15 Figure 16
Figure 17 Figure 18
Loose
Loose
Lock
Figure 19 Figure 20
1. Adjustment of feeding limit
To prevent unwanted penetration to work piece, the feeding limit
shall be set by adjusting the appropriate position of feeding depth
fixing button as long as the distance between the end of tool and
top surface if work piece is measured.
A. Setting of feeding depth
1. Loosen knob A.
2. Turn scaled ring B to desired feeding depth.
3. Lock knob A.
2. Work table and vise adjustment
Loose the work table and vise set screw then turn the work table 180 degree, let the vise be upside.
Then completely tight the set bolt.
Figure 13.14.15.16
6.Please open water outlet valve and adjust a proper water outlet volume after power supplying.
Fig 17
11
Figure 13 Figure 14 Figure 15
Figure 16 Figure 17
Loose
Loose
Lock
Wrench Size 19m
shownin Figure 12. ) If you want to continue to operate, just press down grip handle.(as
shownin
Figure 13.
)
3. Protect safety guard shall be allocated in a proper position in operation. It is controlled by a micro
witch.(For CE)
10
4. Adjustment of feeding limit
To prevent unwanted penetration to work piece, the feeding limit
shall be set by adjusting the appropriate position of feeding depth
fixing button as long as the distance between the end of tool and
top surface if work piece is measured.
A. Setting of feeding depthFeed Depth Adjustment
5.Work table and vise adjustment
Loose the work table and vise set screw then turn the work table 180 degree, let the vise be upside.
Then completely tight the set bolt. Figure 14.15.16.17
Figure 12 Figure 13
Lock
Loose
A
Figure 15