HUSTLER SmoothTrak X-ONE, Руководство оператора, Страница: 143 / 452

606528CE 4-1 REV B
CZ
DA
DE
EN
ES
FR
IT
NL
PT
SV
MAINTENANCE & ADJUSTMENTS
Safe Servicing Practices
Refer to the Safety Precautions section of this manual for
more service safety information.
Service Introduction
Regular maintenance is the best prevention for costly
downtime or expensive, premature repair. The following
pages contain suggested maintenance information and
schedules which the operator should follow on a routine
basis. For more detailed information order the correct Parts
Manual and General Service Manual for your unit. Refer to
the Product Literature section of this manual for more infor-
mation.
Remain alert for unusual noises, which could signal a prob-
lem. Visually inspect the machine for any abnormal wear or
damage. A good time to detect potential problems is while
performing scheduled maintenance service. Correcting the
problem as quickly as possible is the best insurance.
Clear away heavy build-up of grease, oil and dirt, especially
in the engine and hydraulic component areas; minute dust
particles are abrasive to close-tolerance engine and hydrau-
lic assemblies.
Inspect mower daily for grass clippings and wire or string
tangles. The underside of the mower deck will collect a build-
up of grass clippings and dirt, especially when grass is wet or
has high moisture content. This build-up will harden, restrict-
ing blade and air movement which will probably result in a
poorer quality of cutting. Therefore it should be removed rou-
tinely. To do this it will be necessary to raise and block the
deck using jack stands or blocks in the full up position.
Scrape the build-up off from underneath.
IMPORTANT: Seat arm rests – Place the steering control
levers in the park brake position and pivot the arm rests
upward before lifting the seat platform to prevent arm rest
damage.
Some repairs require the assistance of a trained service
mechanic and should not be attempted by unskilled person-
nel. Consult your Hustler
®
service center when assistance is
needed.
Torque Values
Torque values are given below:
N•m
Wheel (lug) nuts . . . . . . . . . . . . . . . . . 95
Blade spindle bolt top. . . . . . . . . . . . . 95
Blade spindle bolt bottom . . . . . . . . 160
Wheel motor nut . . . . . . . . . . . . . . . . 312
Lug nuts only - It is recommended that these be checked
after the first 2 hours of operation, initially, every 50 hours
and following removal for repair or replacement.
For all other torques refer to the mower’s General Service
Manual for standard torque chart. See Product Literature sec-
tion for ordering information.
For engine torque values, refer to the engine owner’s man-
ual.
Tires
It is important for level mowing that the tires have the
same amount of air pressure. The recommended pressures
are:
Drive wheels . . . . . . . . . . . . . . . . . . . . . . 55–83 KPa
Front wheels . . . . . . . . . . . . . . . . . . . . . . 55–83 KPa
If you wish to use non-pneumatic tires on your Hustler
®
mower, the tire must be a Hustler
®
approved tire. Warranty
claims will be denied on any mower equipped with unap-
proved non-pneumatic tires.
Lubrication
Use SAE multi-purpose grease.
Electrical System
IMPORTANT: Refer to the Safety section of this manual for
detailed battery servicing safety information.
The electrical system is a 12 volt, negative ground. The rec-
ommended battery size is:
Garden tractor BCI group U1R with a 225 or better
cranking AMP rating.
A maintenance-free battery is recommended. Otherwise,
follow battery manufacturer’s maintenance, safety, storing
and charging specifications.
Master in-line fuse
These mowers have a master in-line fuse (40 amp) in the
electrical system. This is the main fuse to protect the com-
plete electrical system. It is located next to the starter sole-
Particular attention must be given to tightening the
drive wheel lug nuts and blade spindle bolts. Failure
to correctly torque these items may result in the loss
of a wheel or blade, which can cause serious dam-
age or personal injury.
WA
RNI
N
G