HUSTLER FasTrak Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 37

HUSTLER FasTrak Скачать руководство пользователя страница 15

121363

4-3

REV C

11. The steering control levers should be adjusted so that

they align within ± .125" of each other when in the neu-
tral position. Figure 4-5
NOTE: The space between the ends of steering control
levers should be .50” ± .25”. Figure 4-5

12. Check to make sure all tools or obstructions are

removed from under the mower.

13. Raise the rear of the mower and remove the jack

stands. Lower the mower.

14. Remove the chocks from the front wheels.

Park Brake Spring Adjustment

Occasionally check the park brake spring adjustment using

the following method:

1. This procedure does not require engine power, there-

fore:

• Park the mower on level ground
• Disengage the deck clutch.
• Place the steering control levers in the park brake

position.

• Stop the engine.

• Remove the ignition key.
• Disconnect the negative battery cable.

2. On one side measure the park brake spring. It should

be compressed to 1.43"–1.48". If it is not, adjust the
nylock nut until the proper spring compression is
achieved. Figure 4-6

3. Repeat for other side.

4. Reconnect the negative battery cable.

Do not operate the mower without plugging the
mower’s wiring harness into the seat switch. This
switch is an important part of the safety start
interlock system. Serious injury can result if the
seat switch is not plugged into the mower’s wiring
harness.

Never operate the mower with a non-functioning
seat switch. Always reconnect the seat switch to the
mower harness.

Figure 4-5

WA

R

N

IN

G

WARNING

Align handles

± .125”

.50" ± .25”

A. Nylock nut
B. Park brake spring

C. Park brake rod

Figure 4-6

A

B

1.43"–1.48"

C

«
...
13
14
15
16
17
...
»

Содержание FasTrak






































Отзывы:

Нет отзывов