HUSTLER FasTrak Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 37

HUSTLER FasTrak Скачать руководство пользователя страница 10

REV C

2-4

121363

• Always disconnect the negative (black) battery

cable(s) before disconnecting the positive (red)
cable(s).

• Always connect the positive (red) battery cable(s)

before connecting the negative (black) cable(s).

Avoid Acid Burns



Sulfuric acid in battery electrolyte is poisonous. It is
strong enough to burn skin, eat holes in clothing and
cause blindness if splashed in eyes.
Avoid the hazard by:

• Filling batteries in a well-ventilated area.
• Wearing eye protection and rubber gloves.
• Avoiding breathing fumes when electrolyte is

added.

• Avoiding spilling or dripped electrolyte.

If you spill acid on yourself:

• Flush your skin with water.

• Apply baking soda or lime to help neutralize the

acid.

• Flush your eyes with water for 10-15 minutes. Get

medical attention immediately.

If acid is swallowed:

• Drink large amounts of water or milk.
• Then drink milk of magnesia, beaten eggs or veg-

etable oil.

• Get medical attention immediately.

«
...
8
9
10
11
12
...
»

Содержание FasTrak






































Отзывы:

Нет отзывов