background image

HUSSONG MANUFACTURING CO., INC.

INSTALLATION AND 

OPERATION MANUAL

 

ͷ

Do not store or use gasoline or other 

flammable vapors and liquids in the vicinity 

of this or any other appliance.

 

ͷ

WHAT TO DO IF YOU SMELL GAS

• 

Do not try to light any appliance.

• 

Do not touch any electrical switch; do 

not use any phone in your building.

• 

Leave the building immediately.

• 

Immediately call your gas supplier from 

a neighbor’s phone. Follow the gas 

supplier’s instructions.

• 

If you cannot reach your gas supplier, 

call the fire department.

 

ͷ

Installation and service must be performed 

by  a  qualified  installer,  service  agency  or 

the gas supplier. 

    WARNING:

FIRE OR EXPLOSION HAZARD

Failure  to  follow  safety  warnings  exactly 

could  result  in  serious  injury,  death,  or 

property damage.

This  appliance  may  be  installed  in 

an  aftermarket,  permanently  located, 

manufactured  home  (USA  only)  or  mobile 

home, where not prohibited by local codes.
This  appliance  is  only  for  use  with  the  type 

of  gas  indicated  on  the  rating  plate.  This 

appliance is not convertible for use with other 

gases, unless a certified kit is used.

INSTALLER: Leave this manual with the appliance. 

 

CONSUMER: Retain this manual for future reference.

English and French installation manuals are available through your 

local dealer. Visit our website 

www.kozyheat.com

.

Les manuels d’installation en français et en anglais sont disponibles 

chez votre détaillant local. Visitez 

www.kozyheat.com.

DANGER

HOT GLASS

 WILL

CAUSE BURNS

DO NOT TOUCH

 GLASS

UNTIL COOLED

NEVER

 ALLOW CHILDREN

TO TOUCH GLASS

A  barrier  designed  to  reduce  the  risk  of  burns 

from the hot viewing glass is provided with this 

appliance and shall be installed for the protection 

of children and other at-risk individuals.

B E L L I N G H A M   5 2

Model #BHM-52

Direct Vent Gas Fireplace

Hussong Mfg. Co., Inc. 

BHM-52 Report No: 19-554

Rev.1, May 2020

Starting Serial Number: 

20 300000 26

Содержание Kozy Heat BELLINGHAM 52










































































Отзывы: