background image

CARE AND CLEANING

Long life and satisfactory performance of any
equipment is dependent upon the care it receives.
To ensure long life, proper sanitation and mini-
mum maintenance costs, these merchandisers
should be thoroughly cleaned, all debris removed
and the interiors washed down, at least weekly. 

Exterior Surfaces
The exterior surfaces must be cleaned with a mild
detergent and warm water to protect and maintain
their attractive finish. NEVER USE ABRASIVE
CLEANSERS OR SCOURING PADS.

Interior Surfaces
The interior surfaces may be cleaned with most
domestic detergents, ammonia based cleaners and
sanitizing solutions with no harm to the surface.
Removable parts are labeled R

EMOVE

FOR

CLEANING

Removable stainless steel parts may be cleaned
and sanitized in dishwasher. 

See next page for detailed direction.

Do Not Use:

Abrasive cleansers and scouring pads, as
these will mar the finish.

A hose on lighted shelves or submerge the
shelves in water.

Solvent, oil or acidic based cleaners on any
interior surfaces.

Do:

Remove the product and all loose debris to
avoid clogging the waste outlet.

Store product in a refrigerated area such as a
cooler. Remove only as much product as can
be taken to the cooler in a timely manner.

Turn off refrigeration, then disconnect
electrical power.

Thoroughly clean all surfaces with soap and
hot water. D

O NOT USE STEAM OR HIGH WATER

PRESSURE HOSES TO WASH THE INTERIOR

.

T

HESE WILL DESTROY THE MERCHANDISER

S

SEALING CAUSING LEAKS AND POOR PERFORM

-

ANCE

.

Lift or remove fan plenum for cleaning. Hook
chain in rear panel to secure plenum during
cleaning. Be sure to reposition the fan plenum
after cleaning merchandiser. 

Take care to minimize direct contact between
fan motors and cleaning or rinse water.

Rinse with hot water, but do NOT flood.
N

EVER INTRODUCE WATER FASTER THAN THE

WASTE OUTLET CAN REMOVE IT

.

Allow merchandisers to dry before resuming
operation.

After cleaning is completed, turn on power to
the merchandiser.

P/N 406928

5-1

E

Eu

urro

o D

De

ellii M

Me

errc

ch

ha

an

nd

diisse

errss

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)

M

MA

AIIN

NT

TE

EN

NA

AN

NC

CE

E

ALWAYS SHUT POWER OFF 

DURING CLEANING PROCESS.

WARNING

!

Do NOT use HOT water on COLD glass

surfaces. This can cause the glass to

shatter and could result in personal
injury. Allow glass fronts, ends, and

service doors to warm before applying

hot water.

WARNING

!

Do NOT allow product to sit in a

non-refrigerated area.

WARNING

!

Содержание IMPACT ED1






























Отзывы: