Husqvarna TE 250 страница 23 Скачать руководство пользователя

Страница: 23 / 169

CONTROLS 6

6.18

Opening 2-stroke oil tank cap

V01647-10

–

Fold loop

upward.

–

Turn the 2-stroke oil tank cap counterclockwise and pull it

up.

6.19

Closing 2-stroke oil tank cap

V01648-10

–

Put the 2-stroke oil tank cap on and turn it clockwise.

–

Fold loop

down.

The 2-stroke oil tank cap engages.

6.20

Cold start button

S03529-10

The cold start button

is fitted on the side of the throttle valve

body.
The electronic fuel injection system extends the injection time if

the engine is cold and the ambient temperature is low. To help

the engine burn the increased fuel quantity, it must be supplied

with additional oxygen by pulling the cold start button.

Info

If the engine is warm, the cold start button must be deac-

tivated.

Possible states

• The cold start button is activated

–

The cold start button is

pulled out all the way and turned by a ¼ turn.

• The cold start button is deactivated

–

A further ¼ turn

returns the cold start button back to the basic position.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды