Husqvarna TE 250 Скачать руководство пользователя

Страница: 18 / 169

6 CONTROLS

6.1

Clutch lever

S04405-10

Clutch lever

is fitted on the handlebar on the left.

The clutch is activated hydraulically and adjusts itself automati-

cally.

6.2

Hand brake lever

S04406-10

Hand brake lever

is located on the right side of the handle-

bar.
The front brake is engaged using the hand brake lever.

6.3

Throttle grip

S04406-11

The throttle grip

is fitted on the right side of the handlebar.

6.4

Stop button (All EU/AR/CN standard models)

S04407-10

The stop button

is fitted on the left side of the handlebar.

Possible states

• The stop button

is in the basic position

–

In this position,

the ignition circuit is closed and the engine can be started.

• Stop button

pressed

–

In this position, the ignition circuit

is interrupted, a running engine stops, and a non-running

engine will not start.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды