Husqvarna TE 250 страница 140 Скачать руководство пользователя

Страница: 140 / 169

19 CLEANING, CARE

138

–

Treat bare metal (except for brake discs and the exhaust sys-

tem) with a corrosion inhibitor.

Preserving materials for paints, metal and rubber

(

p. 157)

–

Treat all plastic parts and powder-coated parts with a mild

cleaning and care product.

Special cleaner for glossy and matte paint finishes, metal

and plastic surfaces (

p. 158)

(All EU/AR standard models)

–

Oil the steering lock.

Universal oil spray (

p. 158)

19.2

Checks and maintenance steps for winter operation

Info

If you use the motorcycle in winter, salt can be expected on the roads. You should therefore take pre-

cautions against aggressive road salt.
If the vehicle has been used on salted roads, use cold water for cleaning after riding. Warm water

enhances the corrosive effects of salt.

401060-01

–

Clean the motorcycle. (

p. 137)

–

Clean the brakes.

Info

After

EVERY

trip on salted roads, thoroughly clean

the brake calipers and brake linings, after they have

cooled down and without removing them, with cold

water and dry them carefully.
After riding on salted roads, thoroughly clean the vehi-

cle with cold water and dry it well.

–

Treat the engine, link fork, and all other bare or zinc-plated

parts (except the brake discs) with a wax-based corrosion

inhibitor.

Info

Corrosion inhibitor must not come in contact with the

brake discs as this would greatly reduce the braking

force.

–

Clean the chain. (

p. 76)

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды