Husqvarna TE 250 страница 117 Скачать руководство пользователя

Страница: 117 / 169

ELECTRICAL SYSTEM 15

115

15.11

Adjusting the headlight range

Preparatory work

–

Check the headlight setting. (

p. 114)

H03755-10

Main work

–

Loosen screw

–

Adjust the headlight range by pivoting the headlight.
Guideline

The boundary between light and dark must be exactly on

the lower mark for a motorcycle with rider (instructions on

how to apply the mark: Checking the headlight setting).

Info

If you have a payload, you may have to correct the

headlight range.

–

Tighten screw

15.12

Changing the combination instrument battery

Preparatory work

–

Remove the headlight mask with the headlight. (

p. 111)

H03756-10

Main work

–

Remove screws

with the washers.

–

Pull the combination instrument upward out of the holder.

H03757-10

–

Using a coin, turn protection cap

all the way counter-

clockwise and take it off.

–

Remove combination instrument battery

–

Insert the combination instrument battery with the label fac-

ing outward.

Combination instrument battery (CR 2032) (

p. 150)

–

Check the O-ring of the protection cap for correct seating.

H03758-10

–

Position protection cap

and turn all the way clockwise

using a coin.

–

Press any button on the combination instrument.

The combination instrument is activated.

–

Position the combination instrument in the holder.

–

Mount and tighten the screws with washers.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды