Husqvarna TE 250 страница 101 Скачать руководство пользователя

Страница: 101 / 169

WHEELS, TIRES 14

S04843-10

Main work

–

Manually press the brake caliper toward the brake disc to

push back the brake piston.

Info

Make sure that you do not press the brake caliper

against the spokes when pushing back the brake pis-

ton.

–

Remove nut

–

Take off chain adjuster

. Pull out wheel spindle

far

enough to allow the rear wheel to be pushed forward.

–

Push the rear wheel forward as far as possible. Remove the

chain from the rear sprocket.

Info

Cover the components to protect them against dam-

age.

Warning

Danger of accidents

Damaged brake discs reduce

the braking effect.

–

Always lay the wheel down in such a way that the

brake disc is not damaged.

–

Hold the rear wheel and remove the wheel spindle. Take the

rear wheel out of the link fork.

Info

Do not operate the foot brake lever when the rear

wheel is removed.

H03002-10

–

Remove spacers

14.4

Installing the rear wheel

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды